Results 1 to 5 of 5

Thread: pmRJ update

  1. #1
    Enrico Schiratti
    Guest

    pmRJ update

    Hi,

    I have updated the Build of the RJ, some small graphics changes were made
    and when the FS Autopilot is used (i.e. no MCP is running) I just take the
    normal FS Flight Director deflections.

    The setup programs for the full and demo versions have been refreshed as
    well.

    Ciao

    Enrico


  2. #2
    Thomas Richter
    Guest

    Re: pmRJ update

    Hi Enrico,
    we lost the NAV-2 on PFD. In Standby-Radio-Screen you can see the NAV-2
    Freq. and in ND you can see the change from green to yellow NAV-Point.
    But on PFD there is no NIDLE (blue) and now NAV-ID wit range shown.
    All other is working.

    --
    Best Regards
    Thomas - EW321


    "Enrico Schiratti" schrieb im Newsbeitrag
    news:271450.53888@wb.onvix.com...
    > Hi,
    >
    > I have updated the Build of the RJ, some small graphics changes were made
    > and when the FS Autopilot is used (i.e. no MCP is running) I just take

    the
    > normal FS Flight Director deflections.
    >
    > The setup programs for the full and demo versions have been refreshed as
    > well.
    >
    > Ciao
    >
    > Enrico
    >



  3. #3
    Enrico Schiratti
    Guest

    Re: pmRJ update

    Hi,

    > we lost the NAV-2 on PFD. In Standby-Radio-Screen you can see the NAV-2
    > Freq. and in ND you can see the change from green to yellow NAV-Point.
    > But on PFD there is no NIDLE (blue) and now NAV-ID wit range shown.


    I didn't touch that part of the code at all, but I will check.

    Are you using the MCP?

    Ciao

    Enrico


  4. #4
    Thomas Richter
    Guest

    Re: pmRJ update

    Hi Enrico,
    I don`t use MCP now.
    But just now I changed back to the old *.DLL, then NAV-2 is OK(with new
    *.EXE).
    If I use the new *.DLL NAV-2 in PFD-display is gone.
    It`s a mistake in new DLL-file.
    --
    Best Regards
    Thomas - EW321

    "Enrico Schiratti" schrieb im Newsbeitrag
    news:271476.53888@wb.onvix.com...
    > Hi,
    >
    >> we lost the NAV-2 on PFD. In Standby-Radio-Screen you can see the NAV-2
    >> Freq. and in ND you can see the change from green to yellow NAV-Point.
    >> But on PFD there is no NIDLE (blue) and now NAV-ID wit range shown.

    >
    > I didn't touch that part of the code at all, but I will check.
    >
    > Are you using the MCP?
    >
    > Ciao
    >
    > Enrico
    >



  5. #5
    Enrico Schiratti
    Guest

    Re: pmRJ update

    Hi,

    > But just now I changed back to the old *.DLL, then NAV-2 is OK(with new
    > *.EXE).
    > If I use the new *.DLL NAV-2 in PFD-display is gone.
    > It`s a mistake in new DLL-file.


    It must be... in fact I was doing one thing too fast.

    I will re-upload everything now. Thank you very much for your help!

    Ciao

    Enrico


Similar Threads

  1. PMRJ Update 92
    By N242AM in forum PM RJ GC
    Replies: 10
    Last Post: 12-21-2008, 09:17 AM
  2. N1 Lag- PMRJ software
    By Tomlin in forum PM General Q & A
    Replies: 9
    Last Post: 11-27-2007, 10:12 AM
  3. pmRJ and Navigraph
    By Tim in forum PM General Q & A
    Replies: 2
    Last Post: 09-28-2007, 08:31 PM
  4. PMRJ Wish
    By Marc Nieuwhof in forum PM General Q & A
    Replies: 1
    Last Post: 01-16-2006, 05:34 AM
  5. pmRJ 48b
    By Thomas Richter in forum PM General Q & A
    Replies: 2
    Last Post: 11-21-2004, 04:11 PM