Results 1 to 5 of 5
  1. 05-21-2010, 02:45 PM #1
    rodenhuis
    rodenhuis is offline
    New Member
    Join Date
    Apr 2010
    Location
    France
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Cool drawings & dimensions

    I am new on this forum and looking for drawings or/and dimensions of the pedestal bay and CDU unit assembly bay of the B737. I have been looking on all kinds of forums but still unsuccesfull. A lot of people must have made it so they must be around. Please help.............I am Dutch, living in France. Jackrodenhuis

    Posts: 1
    Joined: Fri May 21, 2010 8:32 pm
    j.rodenhuis@gmail.com
    Reply With Quote Reply With Quote
  2. 05-21-2010, 03:44 PM #2
    Ronson2k9
    Ronson2k9 is offline
    500+ This must be a daytime job Ronson2k9's Avatar
    Join Date
    Apr 2009
    Location
    London, ON Canada
    Posts
    506
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: drawings & dimensions

    First welcome to the forum..

    Depending on the version of the 737 you are inquiring about (there are several) you may find this site .. Another builder quite helpfull
    http://users.skynet.be/jcordon/cockpit/plans.htm

    Cheers
    Ron
    Up Up and away in my beautiful my beautiful - Amphibian
    Reply With Quote Reply With Quote
  3. 05-22-2010, 05:09 PM #3
    rodenhuis
    rodenhuis is offline
    New Member
    Join Date
    Apr 2010
    Location
    France
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: drawings & dimensions

    I have sent Juan the owner of the site a PM. as all the dimensions were not on the site, Thanks Jack
    Reply With Quote Reply With Quote
  4. 05-23-2010, 04:17 AM #4
    Hessel Oosten
    Hessel Oosten is offline
    150+ Forum Groupie
    Tutorial Contributor / Point Value: 10
    Total Awards: 1
    Total Points: 10
    Join Date
    Sep 2006
    Location
    Netherlands
    Posts
    165
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: drawings & dimensions

    Jack,

    Probably of help my tutorial on panel dimensions on the frontpage of this Mycockpit site at this time.

    If you draw/make the panels at the inner side correct, in fact after that, the dimensions of the whole assembly / outer dimensions (e.g. pedestal) do follow logically from these inner dimensions.

    Since we all make small errors with dimensions, following this method (from inner to outer) makes fitting of the final outer housing more accurate in your specific situation.

    Hope this helps,

    Hessel Oosten
    767 Level-D
    Reply With Quote Reply With Quote
  5. 05-23-2010, 04:36 AM #5
    rodenhuis
    rodenhuis is offline
    New Member
    Join Date
    Apr 2010
    Location
    France
    Posts
    3
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: drawings & dimensions

    Hessel, bedankt. Ik ga meteen kijken,
    groeten vanuit een warm Frankrijk
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. 747 Throttle drawings
    By wdibert in forum General Builder Questions All Aircraft Types
    Replies: 8
    Last Post: 07-20-2014, 06:21 PM
  2. 747 Modular Nose Section/ shield drawings/dimensions in centimeters?
    By aron9133 in forum General Builder Questions All Aircraft Types
    Replies: 0
    Last Post: 02-03-2011, 02:09 PM
  3. Boeing 737 NG Drawings and Dimensions
    By vybhav in forum MyCockpit Support:
    Replies: 1
    Last Post: 08-01-2009, 09:41 AM
  4. Drawings
    By nihad in forum General Builder Questions All Aircraft Types
    Replies: 9
    Last Post: 05-27-2008, 01:40 PM
  5. 737ng CAD drawings
    By Edc in forum General Builder Questions All Aircraft Types
    Replies: 0
    Last Post: 11-07-2007, 05:38 PM

Tags for this Thread