Results 1 to 10 of 10
  1. #1
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Measurement needed if you know...

    What is the distance from the front edge of the glareshield to the bottom of the center windscreen support for the 737?

    This is one that I haven't been able to find.

    Also, does anyone know what the angle of that windscreen support is?
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  2. #2
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,412
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Mike, email me and I'll reply with some schematics I have...

    Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  3. #3
    150+ Forum Groupie Radar's Avatar
    Join Date
    Jan 2007
    Location
    CANADA
    Posts
    243
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    http://www.thefreeemoticons.info/images/flags/smilies0949.gif

  4. #4
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks Radar, but the one I need is not there.

    Good to see you around again!
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  5. #5
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thank Gwyn!
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  6. #6
    300+ Forum Addict
    Join Date
    Mar 2007
    Location
    Norway
    Posts
    415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Well, what was the number? Curious because My mip is more or less finished but I never had this number. Would be fun to check

  7. #7
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,881
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    There is no direct measurement for that dimension. It has to be extrapolated based on other given measurements. I haven't had the time to go through it yet, but it was the same set of dimensions you pointed me to several weeks ago.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  8. #8
    300+ Forum Addict
    Join Date
    Mar 2007
    Location
    Norway
    Posts
    415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    aha, thanks

    Getting proper measurements is the biggest enemy at this hobby

  9. #9
    25+ Posting Member Fuglsang's Avatar
    Join Date
    Jun 2007
    Location
    T鴕ring, Denmark
    Posts
    55
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by ivar hestnes View Post
    aha, thanks

    Getting proper measurements is the biggest enemy at this hobby
    Hehe.. Your totally right Ivar!

  10. #10
    25+ Posting Member
    Join Date
    Jul 2007
    Location
    Port Kembla (near YWOL), Australia
    Posts
    42
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi,
    i found this in my travels around looking at people's cockpits.
    I was going to upload the PDF file here but thought it may be the wrong thing to do, so i will post a link to the page i found it on & the link to get the compiled PDF file.
    It does not give the dimension directly but is a good collection of images that may make approximating the size a little easier.

    All the best
    Gerry

    http://www.737ng.co.uk/technical.htm

    http://www.737ng.co.uk/B737%20measurements.pdf

Similar Threads

  1. measurement confirmation
    By Jackpilot in forum General Builder Questions All Aircraft Types
    Replies: 5
    Last Post: 05-29-2009, 08:05 AM
  2. 747 MIP measurement
    By visualchaosfx in forum Where to Start Building a Home Cockpit
    Replies: 5
    Last Post: 02-28-2007, 05:00 PM