Results 1 to 4 of 4
  1. 01-07-2011, 09:55 AM #1
    nax228
    nax228 is offline
    300+ Forum Addict nax228's Avatar
    Join Date
    Oct 2008
    Location
    Oslo
    Posts
    316
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Yoke pots to BU0836x ports

    Witch ports in the Leobodnar BU0836x shall I connect my two yoke potmeters to?
    I have done a few searches, but can't seem to find a 100% answer, and I want to do it right the first time.
    NAX
    http://www.mycockpit.org/forums/show...slo?highlight=
    Reply With Quote Reply With Quote
  2. 01-07-2011, 10:15 AM #2
    Atomic_Sheep
    Atomic_Sheep is offline
    150+ Forum Groupie Atomic_Sheep's Avatar
    Join Date
    May 2010
    Location
    Melbourne, Australia
    Posts
    166
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Yoke pots to BU0836x ports

    Have a read of my thread... I believe the answer you seek is in one of the replies.

    http://www.mycockpit.org/forums/show...elp?highlight=
    Reply With Quote Reply With Quote
  3. 01-07-2011, 12:01 PM #3
    ian@737ng.co.uk
    ian@737ng.co.uk is offline
    500+ This must be a daytime job
    Builder Of The Month / Point Value: 100
    Total Awards: 1
    Total Points: 100
    ian@737ng.co.uk's Avatar
    Join Date
    Jan 2006
    Location
    Oswestry, Shropshire
    Posts
    604
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Yoke pots to BU0836x ports

    hello nax.......
    connect the yoke axes to the X axis & Y axis inputs to the card. this will allow you to set the 'centred' position in the windows calibration page in the control panel.
    makes life very easy. then if you have a registered version of FSUIPC, you can tweak the inputs and the response curve in there.
    hope that helped you out captain......
    regards from wales...

    ian
    Mr. Ian. P. Sissons is hereby recognised as an Honorary Flight Sim Captain following his passing in February 2016. This is in recognition for his commitment to Flight Simulation.

    www.mycockpit.org Featured Builder August 2008 www.737ng.co.uk
    FS9/PROSIM737/CPFLIGHT/Lots of BU0836X's and a Beer Fridge
    Reply With Quote Reply With Quote
  4. 01-07-2011, 12:58 PM #4
    nax228
    nax228 is offline
    300+ Forum Addict nax228's Avatar
    Join Date
    Oct 2008
    Location
    Oslo
    Posts
    316
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Yoke pots to BU0836x ports

    Ta Daaa

    Solved

    Thanks a lot guys
    NAX
    http://www.mycockpit.org/forums/show...slo?highlight=
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Cessna Yoke Column - Yoke Movement ?
    By Ronson2k9 in forum General Aviation (GA) Builder Disccusion
    Replies: 2
    Last Post: 04-20-2010, 12:09 PM
  2. Pots on a BU0836X
    By colaboy in forum General Builder Questions All Aircraft Types
    Replies: 2
    Last Post: 08-07-2009, 12:58 PM
  3. Pots 101
    By ak49er in forum General Builder Questions All Aircraft Types
    Replies: 10
    Last Post: 06-23-2007, 07:28 PM
  4. Analog Pots for 737 Yoke
    By Jeff C. in forum Phidgets & Cockpit Simulator Builder
    Replies: 1
    Last Post: 10-09-2005, 08:47 AM

Tags for this Thread