Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2005
    Location
    VHHH
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    LED64 for 3v KLED?

    hi everyone,

    Have a simple questuion before purchase, does the LED64 support 3v LED light?

    Thank you.

    Alkit

  2. #2
    phidgets
    Guest
    Yes


    Matt

  3. #3
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2005
    Location
    VHHH
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    LED64 for 6v LED ??

    I just found a lower voltage lamp replacement (LED) for my cockpit's Korry 387 light, which is perfectly for the current lamp hardware. But it takes 6V. Can they be powered by the LED64?

    Thank you.

  4. #4
    imported_MattO
    Guest
    Just a guess here.... I doubt it... LED's only use 20 Ma bulbs require, quite a bit more.

    Matt O.

  5. #5
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2005
    Location
    VHHH
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    That 6v LED take 20ma current. I look up the instruction sheet of my LED64 and I cannot find any info of what range of LED light can be used. Like the voltage range....

    I need to know whether the borad can operate it before buying it.

    So, hope you guys can help.

    Alkit

  6. #6
    imported_MattO
    Guest
    Oops, I thought you meant a 6V lamp.

    Matt O.

  7. #7
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2005
    Location
    VHHH
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    so....will 6V LED work with the LED64 card???

    thx!!

    Alkit

  8. #8
    alandyer
    Guest
    You coud use original Korry 28V bulbs.
    Have a look at Interfacekit documentation.
    On the Featured Cockpits page there is pic and specs from a builder using Korrys.

  9. #9
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Mar 2005
    Location
    VHHH
    Posts
    7
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Exclamation

    Perhaps, I state my question again. Make it simple.

    "Can LED64 board operate 6v LED light ? "

    That's all I want to ask.

    Thank you!!

    Alkit

  10. #10
    alandyer
    Guest
    Looking at phidgets LED64 hardware documentation.
    http://www.phidgets.com/modules.php?...rtid=21&page=1

    Board's maximum power supply is limited to 8W - up to maximum of 12V.

    Using 6V power supply, 8W would permit total current of 1.333 Amps
    or slighly more than 0.02 Amps for each of the 64 LEDs.

    Let's get Matt to confirm that.

Page 1 of 2 12 LastLast

Similar Threads

  1. Led64 error 380
    By KenK in forum FS2Phidget Users
    Replies: 3
    Last Post: 02-23-2009, 05:38 PM
  2. LED64 and FDS SIX PACK
    By Peter Nielsen in forum Phidgets & Cockpit Simulator Builder
    Replies: 0
    Last Post: 12-04-2007, 05:29 AM
  3. Anyone want to sell an LED64?
    By exabrial in forum FS2Phidget Users
    Replies: 5
    Last Post: 10-05-2006, 09:56 PM
  4. LED64 vs. 0/16/16
    By janpedersen in forum Phidgets & Cockpit Simulator Builder
    Replies: 1
    Last Post: 08-24-2005, 05:31 AM
  5. How to dim LED with LED64?
    By Jan Pemöller in forum FS2Phidget Users
    Replies: 19
    Last Post: 02-23-2005, 06:40 AM