Results 1 to 6 of 6
  1. #1
    500+ This must be a daytime job JBaymore's Avatar
    Join Date
    Mar 2005
    Location
    Wilton, New Hampshire USA
    Posts
    601
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Question CAn I coonect two LED's in parallel on LED64?

    Hi all. Just got the LED64 unit. I have two questions.

    First question............

    Is there any reason that I cannot connect two LEDs in parallel on a single "output"? The annunciators from Flight Deck Solutions are designed to have two LED's mounted in them. Of course for the indicvators that I might want to have a red and a green LED in it to show "state" .... that works great being driven by two circuits. But a single led, even a high intensity one ... sitting on one side .... will not illuminate the annunciator very evenly. I can accept this for the two color situation.


    Second question.........

    Can I drive something like a small reed relay off one of the outputs of the LED64? I want to be able to control something other than a LED when a certain state is "true".

    Appreciate the help in advance.

    best,

    ......................john

  2. #2
    Steve Daly
    Guest
    I know nothing about this John...but you should be able to trigger a MOSFET transistor from the LED64 output stage...MOSFETs are what are used in electronic speed controls, you know they can handle a fair bit of current.

  3. #3
    75+ Posting Member
    Join Date
    Jan 2005
    Posts
    75
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi JBaymore,
    I too have the LED 64 and with what your asking..I believe you can get away with paralling 2 leds on i output.
    I myself have not tried it but I think it will work; except if 1 led goes out they both do.
    As for how many leds you connect with this method?...I would not recmend it.
    Try to keep 1 led per output preferred..sneek a 2nd led if you MUST ONLY.

    As for driving a reed switch from this board...no; the reed switch works on a magnet passing past it pulling the tiny switch closed.


    Kind regards
    James

    www.biagettis.com/737simproject

  4. #4
    500+ This must be a daytime job JBaymore's Avatar
    Join Date
    Mar 2005
    Location
    Wilton, New Hampshire USA
    Posts
    601
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    James,

    Thanks for the info.

    What I might do is try two leds to even out the light in the annunciator... but use lower light output ones.... that draw less current each... to keep the mils under control.

    Also .... not a reed SWITCH... but a reed RELAY. A small low current primary relay that I can use to "switch" other higher load stuff. I know I can get the heavy duty relay Phidget card.... but for what I want that is serious overkill. Plus I want to have some double pole double throw type logic on some indicators.

    best,

    ..................john

  5. #5
    75+ Posting Member
    Join Date
    Jan 2005
    Posts
    75
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    My mistake John..didnt see the key word "relay"

    I havnt used one yet..so I cant say..but lead the way for us and let us know!

    James

  6. #6
    Our new friend needs to reach 10 posts to get to the next flight level
    Join Date
    Jun 2004
    Posts
    5
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    The only problem with this is that LEDs will turn on at slightly different voltages. So one LED could fire up and consume all the current. If you put a small resistor in series with each led, and then parallel them, this will work fine. Try 50 Ohms for the resistors.

    This will not work well for white/blue leds. For most red/green/yellow leds, there is enough voltage headroom that a resistor will not affect the brightness.

    Chester

Similar Threads

  1. LED's?
    By Cooleo in forum Where to Start Building a Home Cockpit
    Replies: 1
    Last Post: 09-05-2009, 08:26 PM
  2. USB Parallel Adaptor
    By wanderer in forum OpenCockpits General Discussion
    Replies: 0
    Last Post: 03-07-2008, 12:42 PM
  3. Pre Wired LED's
    By Holclo in forum Computer Hardware Setup
    Replies: 7
    Last Post: 03-01-2008, 01:59 PM
  4. Led64 card and LED in parallel?
    By Olympic260 in forum Phidgets & Cockpit Simulator Builder
    Replies: 3
    Last Post: 11-29-2007, 10:03 AM
  5. FS9 and FSX parallel with PM possible?
    By Norbert-EDDV in forum PM General Q & A
    Replies: 3
    Last Post: 09-12-2007, 03:58 PM