Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    imported_dutch
    Guest

    Question just another newbie question

    Hello....again.

    As in another thread discribed, I've modified some servo's getting a 270 degree turn (simply removing the stopping notch). If I turn the servo by hand, 270 degree rotation is possible, only the FS2Phidget software still shows a maximum of 180 degress in the calibration menu ? So how I can get my 270 degrees range to work ?

    Thanks, Dan

  2. #2
    alandyer
    Guest
    Dutch,

    I will modify calibration page to allow greater range.
    Will let you know when that version is available for download.

    Regards,
    Alan.

  3. #3
    alandyer
    Guest
    Dan,

    My apologies. Called you Dutch.

    Alan.

  4. #4
    alandyer
    Guest
    Dan,

    Download version 2.0.10 of FS2Phidgets.

    Open INI file for servo with text editor such as Notepad.
    File name will be something like PhidgetServo647.ini
    Should be loacted in directory where you installed FS2Phidgets.
    Usually, C:\Program Files\FS2Phidget\

    Add the following entry for any servo you wish to have calibrated beyond the usual 180 degrees of travel.

    [Output 0]
    FSID=THROTTLE_LEVER_8
    Enabled=True
    Invert=False
    SMin=45
    SMax=135
    ServoMax=240 <------- Add this line.

    This is max value you want to see on calibration screen (the max rotation supported by your servo and the phidget card).

    I have not tried this on a servo with rotational capabilities beyond 180 degrees.

    You are now officially a test pilot

    Regards,
    Alan.

  5. #5
    phidgets
    Guest
    Quote Originally Posted by dutch
    Hello....again.

    As in another thread discribed, I've modified some servo's getting a 270 degree turn (simply removing the stopping notch). If I turn the servo by hand, 270 degree rotation is possible, only the FS2Phidget software still shows a maximum of 180 degress in the calibration menu ? So how I can get my 270 degrees range to work ?

    Thanks, Dan
    Hello,

    Alan asked me to ring in on the Phidgets capabilities for servo control. The Phidgets servo controller can accept values from -23 to 232 and that supports a pulse range from 0 microseconds to 2.7 microseconds. To know what your servo will respond to and what it's limits are you will need to refer to it's specs. How far a servo will turn is determined by it's properties not the signal we are sending to it. What I mean by that is, either a servo is made to achieve a certain degree of movement or it isn't. Our range of microsecond pulses that we can send far exceeds the signal specs on any servo.


    The potentiometer inside the servo determines how much it can turn. You can't surpass the potentiometers limits of course. By removing the stop tab you might gain a few more degrees, but you run the risk of destroying the pot. If you remove the pot, then you have a continuous turn servo which will never know what it's own position is.

    We are always open to hearing about servos out there that have large degrees of movement. If someone finds one that can do 270 - 360 I would stock it in a minute. But so far all my testing has come up dry for a good servo which moves more than 180

    I hope this helps out

    Matt

  6. #6
    imported_dutch
    Guest
    Hello

    Thanks ! Will try this out this weekend...I'll let you know !

    Regards,Dan

  7. #7
    imported_dutch
    Guest

    it works!

    Hello

    Thanks, Alan ! Would like to tell you, that you program update is working. Only have to remove the 180 degree limiter notch on the servo gear. Now the program shows 270 degress in calibration screen, also the servo is making 270 degree turns.
    So my first analog oil pressure indicator is working now !

    Regards,Dan

  8. #8
    imported_dutch
    Guest
    Hello...again

    Just found out, if I saved my config, the Invert function will not being saved. Have to select Invert again, if I load the software new.
    Is that known ?

    Regards,Dan

  9. #9
    phidgets
    Guest
    Quote Originally Posted by dutch
    Hello

    Thanks, Alan ! Would like to tell you, that you program update is working. Only have to remove the 180 degree limiter notch on the servo gear. Now the program shows 270 degress in calibration screen, also the servo is making 270 degree turns.
    So my first analog oil pressure indicator is working now !

    Regards,Dan
    Hi Dan,

    Could you please tell us which servo you are using?

    Thanks

    Matt

  10. #10
    imported_dutch
    Guest
    Hello

    I'm using ProTech B-305 standard servo's....very cheap

    Regards,Dan

Page 1 of 2 12 LastLast

Similar Threads

  1. Newbie question - maybe wrong area
    By Gazza321 in forum General Builder Questions All Aircraft Types
    Replies: 4
    Last Post: 06-10-2010, 11:08 AM
  2. Newbie Question on PM and PMDG
    By vybhav in forum PM General Q & A
    Replies: 1
    Last Post: 01-25-2010, 07:30 AM
  3. Newbie question on Potentiometers
    By matta757 in forum General Builder Questions All Aircraft Types
    Replies: 6
    Last Post: 11-24-2009, 08:41 PM
  4. Newbie Question: Which Airplane??
    By trauma2005 in forum Where to Start Building a Home Cockpit
    Replies: 5
    Last Post: 03-22-2009, 09:33 AM
  5. Newbie question
    By David Lee in forum Phidgets & Cockpit Simulator Builder
    Replies: 3
    Last Post: 10-02-2004, 09:52 PM