Results 221 to 230 of 561
Thread: A320 FMGS B47
-
05-04-2017, 09:26 AM #221
- Join Date
- Jan 2007
- Location
- Italy
- Posts
- 204
Re: A320 FMGS B47
Hi, despite the fact i have setup the irs off position in Ittcreator when i start the FMGS they goes to Nav in the software overhead, can you have a look?
thank you
-
05-04-2017, 10:45 AM #222
- Join Date
- Oct 2013
- Location
- Germany
- Posts
- 196
Re: A320 FMGS B47
I don't insist to say that my problem is due to the change of navdata source. I've noticed this kind of LOC offset (30 m) in EDDK just after having changed from Aerosoft to Navigraph. I agree that this might be a pure accident without any correlation. But how are these LOC offsets caused?
The AFCAD file is correct so far. If you can exclude a navdata problem it must probably be a scenery issue.
Regards
René
-
05-04-2017, 11:47 AM #223
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: A320 FMGS B47
The AFCAD file for instance may not be accessible if P3D runs at the same time, depending on many factors (P3D running as admin, installed in a protected windows folder, etc).
Also, if in latest cycle EDDK runways or ILS changed (because of mgnetic variation), then you can have many issues.
Make sure you have applied Hervé Sors ILS fix (not the mag var one, but the navaid ILS one).
Make sure you have used admin rigths when creating the navdata (go to FMGS Server folder and run only the FMGS server using right click -> admin rights).
Make sure you have closed down P3D/FSX when creating the navdata.
JL
-
05-06-2017, 07:47 AM #224
- Join Date
- Feb 2015
- Location
- Austria
- Posts
- 49
Re: A320 FMGS B47
Hello,
unfortunately that was not the solution. I still have crashes with hardware connect during flight. I have seen in the log, that the cpflight Port open and close in a 5 seconds cycle. Is that normal?
Robert
-
05-06-2017, 08:34 AM #225
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: A320 FMGS B47
Do you have a cpflight FCU?
-
05-06-2017, 12:24 PM #226
- Join Date
- Sep 2010
- Location
- LGTS
- Posts
- 424
Re: A320 FMGS B47
Hi
As soon as A/C reaches 180NM from destination, red ENTER DEST DATA msg appears on MCDU. I fill in all parameters in APPR page but the red msg remains. It disappears only by pressing CLR. Is this normal? Do I forget something?
Regards
-
05-06-2017, 01:13 PM #227
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: A320 FMGS B47
Normal.....
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 DislikesLeonidas thanked for this post
-
05-06-2017, 04:44 PM #228
- Join Date
- Feb 2015
- Location
- Austria
- Posts
- 49
-
05-07-2017, 12:17 PM #229
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
Re: A320 FMGS B47
Is it working? because if the port opens/closes every few seconds:
1) it is not connected to that PC
2) it is not the correct port being used
3) in any case, it will not work...
-
05-07-2017, 12:18 PM #230
- Join Date
- Sep 2010
- Location
- LGTS
- Posts
- 424
Candid connections: Platform for casual relationships Live Women Prime Сasual Dating
Super Сasual Dating - Genuine...