A320 FMGS B45

[asessa]

works fine for me - both HW and SW Clients.
when installing Win10 i had to reinstall EHID.
But no change with the latest FMGS update.
the EHID allows for various levelss of log file details. Look in there for clues.

HiStephen, it worked at last.


I restarted the A320_Ehid service and it worked.


I don't know why it didn't work at start. The only change i made between last flight and yesterday was the upgrade of p3d to 3.2.3 version from the 3.1.


In any case, this update works very very well, good job JL!

[SSO]

Jean Luc,

Any thoughts on the VATSIM issue?

Further two notes:
1 - I note in the latest version that the keyboard digits above the QWERTY are no longer accepted as input.
Could this be reinstated as well as the "/" above the "7" key?
2 - The new check of synced Altimeter settings. Could I request an option to sync the two? I am running a single seater Sim and this will always be an issue. The best way for me would be if one is changed - the other was adjusted accordingly regardless of which was changed...

That would be great

[Firefly77]

Hi Jean Luc,

I updated to B45.4 and now intercomm app save some stuff however not everything ??? The selected CPT Microfone is not saved by using the save settings button ? Pls advice.

Best regards

Mic

[OmniAtlas]

Hello just a few things I've noticed with the latest update --

Intercom now runs, however as Mic also mentioned, settings are not saved.

I assigned a PTT PUSH without a release button and had a notification that the mic was open -- so it seems the logic is working.

I am still trying to determine how to integrate this with the setup, apparently it will only work if you have the necessary hardware (skalarki ACP?) -- or would it be possible for someone to write a software panel we can interface with?

*After landing the aircraft the GPWS notification lights up -- I am not too sure if this is normal behaviour.

*My FDS MCDU screen brightness knob is no longer working again...I don't know if this has anything to do with hardware connect crashing, and resetting the switch? I will do more testing.

*Air-conditioning sound level is linked to "avionics" in the sound module and not "AirConditioning"

Otherwise, thank you for the update, and looking forward to B46 with the LNAV/VNAV adjustments.

I would like to hear how all of you are using intercom with your setup and vatsim/ivao.

Thank you,

Ben

[masterp]

Hi JL,
Do you have a plan to simulate Back-Up Speed Scale (BUSS) for FMGS. It is optional but that will be great if we have this




I tested on FMGS by turned off triple ADRs, then I did not know what is current spd of the bus, may be I need to open slide window and check speed with my hand, j/k



Thanks

[Fritz]

With the update to version 45.3 beta my ACC Press gauge is working again.
I made a new assignment in IIT Creator for the Passenger SYS ON Light LED. Haven't seen that is was implemented. However, these lights constantly. The OXYGEN TMR RESET switch on the overhead panel Maintenance is not yet implemented. Is there a another option, or should I delete the assignment again?
Some sound files are corrupted. Have replaced it with files from previous versions.
I am using skalarki TQ Model 2012 with the new profiler. The Trim wheels do not reset to 0° after landing.

Additional:

Since version 45.x I can not initiate descent in managed mode at the top of decend.
The speed accelerated slightly and the altitude remains unchanged. I must first initiate
the descent manually. When I changed to managede mode again then it works.
In version 44.x I did not have this behavior. (FCU from CPFlight) Can anyone confirm this behavior?

Bug with minor priority.
When I press the CVR TEST switch the CVR TEST sound is not sound.
I have already checked the switch assignment in IITCreator.

The initial status of the parking brake is not recognized. Don't know why but he responds immediately when I press the Rudder Trim reset.
Both are assigned with the SIOC Creator. I have to examine in more detail for this issue.

[argileh]

Filippo: the intercom application is just like the real aircraft intercom system.
You have for each seats different microphones and speakers/headphones possibilities. Each of these mikes/phones are linked together using the ACPs panels, so for instance the pilots can talk to each other in flight using the headsets (because of the ambient noise...), or one pilot can talk to the ground crew while the other talks to the ATC etc...
The full ACP panels logic is there, including volume control (though you still need to adjust the volume in windows to adapt to the max sound levels, be careful with you ears...). The VOR/ADF/ILS/MKR morse code IDs are generated in real time as well (if you use that, you should mute the MKR sounds in the older Sound Application).

JL

Is there a need for ACP hardware (e.g. Skalarki ACPs) to be able to have two headsets w/mics communicate with each other - of course aside from two simple/cheap USB sound cards.

i.e is the JH ware alone enough. I tried by setting up the two headsets in the intercom module but was not able to have them communicate/listen to each other.

[Leonidas]

[jeehell]

Hi everyone,

many anwsers below:

Since version 45.x I can not initiate descent in managed mode at the top of decend.
The speed accelerated slightly and the altitude remains unchanged. I must first initiate
the descent manually. When I changed to managede mode again then it works.
In version 44.x I did not have this behavior. (FCU from CPFlight) Can anyone confirm this behavior?

Bug with minor priority.
When I press the CVR TEST switch the CVR TEST sound is not sound.
I have already checked the switch assignment in IITCreator.

The initial status of the parking brake is not recognized. Don't know why but he responds immediately when I press the Rudder Trim reset.
Both are assigned with the SIOC Creator. I have to examine in more detail for this issue.

I will have a look at the managed DES issue. Do you start teh DES at/before/after TOD ?
CVR test logic is working, please check the FCOM.
SIOC/PrkBRK: the initial states of switches in SIOC is never defined. You need to recycle switches so they are detected, this is a know SIOC/opencockpit issue.

Do you have a plan to simulate Back-Up Speed Scale (BUSS) for FMGS. It is optional but that will be great if we have this

No.

Hello just a few things I've noticed with the latest update --

Intercom now runs, however as Mic also mentioned, settings are not saved.

I assigned a PTT PUSH without a release button and had a notification that the mic was open -- so it seems the logic is working.

I am still trying to determine how to integrate this with the setup, apparently it will only work if you have the necessary hardware (skalarki ACP?) -- or would it be possible for someone to write a software panel we can interface with?

*After landing the aircraft the GPWS notification lights up -- I am not too sure if this is normal behaviour.

*My FDS MCDU screen brightness knob is no longer working again...I don't know if this has anything to do with hardware connect crashing, and resetting the switch? I will do more testing.

*Air-conditioning sound level is linked to "avionics" in the sound module and not "AirConditioning"

Otherwise, thank you for the update, and looking forward to B46 with the LNAV/VNAV adjustments.

I would like to hear how all of you are using intercom with your setup and vatsim/ivao.

Thank you,

Ben

Regarding the intercom saving : I will release a new version soon it will solve that. For now, only the CPT headset mike and oxy masks are not saved, everything else is.
Hardware ACPs are required for now. I plan to make a soft version, but this takes time.
Air conditonning and avionics : my tests show they are correcly linked... They sound mostly the same...
GPWS: I have no idea, I need more info (aural warning or not).

Any thoughts on the VATSIM issue?

Further two notes:
1 - I note in the latest version that the keyboard digits above the QWERTY are no longer accepted as input.
Could this be reinstated as well as the "/" above the "7" key?
2 - The new check of synced Altimeter settings. Could I request an option to sync the two? I am running a single seater Sim and this will always be an issue. The best way for me would be if one is changed - the other was adjusted accordingly regardless of which was changed...

I actually do not care much about VATSIM/IVAO/any other. I tried to implement compatibility, but they lack most functions of the XPDR and maintaining that is a nightmare. So I'll have a look one day when I feel like to, no needs to ask it won't help.

1. The MCDU keys can now be adjusted in the CPTkeys.ini or FOkeys.ini file which is in the MCDU application folder. Details are inside.
2. I cannot adjsut to everyone's needs, I might add an option one day but not for now, I have much more important work going on.

[masterp]

Hi JL,
Thanks for your response.
With previous B44 and earlier version, we can switch Transponder between Standby/Off and Mode C.
But with 45.3 in MCDU , both options are blue up and I can not get Mode C active as below picture


Thank alot