A320 FMGS B31

[ToTom]

Strange.
Everything works in my setup. With and without TOPCAT. With and without real weather.
I attach screenshots:
https://www.dropbox.com/sh/bg0p1e8he0co0de/y1zlBCoinH


When I use TOPCAT, prepare load, then I'm doing exports. Then send (not save).
P3D2.1 without the hotfix.
Maybe TAT/SAT is wrong?


What you have language in windows? Maybe here is the problem:
http://www.nirvanatec.com/support/regional_sett.htm

[OmniAtlas]

Strange.
Everything works in my setup. With and without TOPCAT. With and without real weather.
I attach screenshots:
https://www.dropbox.com/sh/bg0p1e8he0co0de/y1zlBCoinH


When I use TOPCAT, prepare load, then I'm doing exports. Then send (not save).
P3D2.1 without the hotfix.
Maybe TAT/SAT is wrong?


What you have language in windows? Maybe here is the problem:
http://www.nirvanatec.com/support/regional_sett.htm

Hi ToTom -- can you try installing P3D2.1 with the hotfix? That may be the problem, it is the only other thing I have installed in P3D besides the 32.2 upgrade. I am using OPUS. TAT/SAT temperatures are reasonable - ~ 23 degrees (YBBN)

My regional language... just english/american I think...I don't think that should matter because it was working fine before.

If it is not a flap/spoilers problem (all are retracted), then somehow I think the AP (FCU) is not communicating correctly with the aircraft to tell it to pitch correctly, especially when in CLB throttle mode.

[ToTom]

I do not installed the hotfix, because I do not use a2a aircraft. Is there any other reason to install this hotfix?
Have you tried FMGS with FSX?

[OmniAtlas]

Well, did another test -- I can climb in TOGA mode...albeit slowly. Once I go to CLB mode the aircraft fails to climb.

Too heavy? But I have put minimal fuel, and weights....

[OmniAtlas]

I do not installed the hotfix, because I do not use a2a aircraft. Is there any other reason to install this hotfix?
Have you tried FMGS with FSX?

I have removed FSX.

[ToTom]

Try this saved flight:
https://www.dropbox.com/s/2172x9ty6u...flight_P3D.zip
And, for example, this route:
EPKK25 SUDOL L619 NUDRO L619 DENKO L996 CHO EPSC

PS. I installed the hotfix. Everything works fine.

[SimStar001]

hello jeehell, after the todays update the ND on captains side isnt working anymore. display stays dark.... yesterday It worked fine.... any idea what could be the problem? ND is connected to the server..


best regards. marco

[tcane]

@Tcane: this script could not work correctly in B32.2. Maybe you had the correct flaps setting in your FS model, but the EWD most probably showed incorrect values for the flaps.

It is NECESSARY to use the flaps controls offered by my software. If you use an opencockpit axis, you can declare it in SIOC Creator in the MISC tab (axis 1 to 16), then you must configure the Axis in FMGS Config as you would with a regular joystick axis.

JL

Hey Jl,
today i try your recommendation. I have made a new fresh installation of your software and made the autoupdate. I declare the two opencockpit axis from the Flaps and Spoilerlever in your SIOC Creator, so like you say it, and assign after in the FMGS Config as a Joystick. It has also recognized both axes. So far so good. The Flaps axis could not be move the controller, but there were data output to calibrate the detents. I think this is normally because i got this same issue by the ruder pedals sometimes.
But when i have started all, i can not move the Flaps... no sounds, nothing. The Spoiler works fine and well.
In this picture you can see that both axis assign.

I hope you or somebody can help me with this... :,(

Florian

[jeehell]

Hello,

@Tcane: easy issues first: your error zone is WAY too big. Use 20 maximum in your case. You should use a value of around 10% of the total range of your axis, here you go from 0 to 255 so 10% is around 25. 20 should be fine also, this allows each detent not to overlap with the next one (for example FLAPS 0 is 3, plus 20 it is 23 which is less than flaps1-20=43 , so no overlaping here). If you use a SIOC analog axis for you rudder, you probably have the same issue with neutral zone!


@Simstar: no idea, for me it works correctly. As said already in several threads, since B32, there is no longer any ND.exe to run. You must run the shortcuts located in EIS folder if you want to start the software manually. Or run using the starter.
Also, if you (re)installed the complete suite, please use the B32.2 installer.

@OmniAtlas: If weight & balance is not the issue, nor the flaps/splrs/gear, then I can only see an issue with your weather addon. Some create strange things in P3D as far as I know. Please try with the default P3D weather system (use the default clear sky theme).


JL

[Stephan Schwarz]

hello jeehell, after the todays update the ND on captains side isnt working anymore. display stays dark.... yesterday It worked fine.... any idea what could be the problem? ND is connected to the server..


best regards. marco

Well, I am glad I am not alone ... I will reinstall (once again) this evening and report if the fault is gone then.

JL: I did start as you said, the ND.exe in the EIS folder manually. Makes no difference, unfortunately.