A320 FMGS B31

[Stephan Schwarz]

I have now completely reinstalled the B32.2 on all 3 PCs, first circling over Seattle was fine and without any freezes.

Regards,
Stephan

[OmniAtlas]

Fixes are inbound according to Jeehell on the buglist website; so hopefully we will see a new FMGS release soon. Thanks JH

And for those and me wondering -- 'jeehell' any significant with that name (french?)

[tcane]

Hi,

@Tcane: as I said, the flaps issue is the only big one. I'll try to correct that today....

Oh, and I thought there would only be a problem with the sound and not with the moving of the flaps lever also. Had a misunderstood. Is the new update already finished an ready for download? Then i will try this afternoon.

[Leonidas]

Hi to all.
Thanks JL for update.
Some issues after a couple of flights:

1. The remaining sound of flaps, that someone else wrote about too.
2. The button "Show/Hide Unnecessary Windows" doesn't work.
3. Clients windows (PFD, ND etc) freeze and a frame "Out of memory" apperars. I've never seen it before. I suppose there is something about the all new EIS.exe. I should restart starter in order to continue my flight.
4. When I disconnect A/T before landing these known messages appear on EWD: "AUTO FLT A/THR LIMITED" (RED), "THR LEVERS.....MOVE" (BLUE). In other words I can't land it manually.
Regards

[Storm24]

Hello I installed B32 with OC Throttle plates running.
1 - After setting MCDU and ready to take off, the FCU not enter into managed mode only works when on the ground.
2 - In flight in the MCDU PERF page is in dispononivel.
3 - Alignment IRS takes 10min, Is there a way to be faster?
4 - APU also takes some time, no way to be faster?
5 - Detent position CL does not appear in ND N1.

Best Regards
Paulo

[Miatanet]

Hello I installed B32 with OC Throttle plates running.
1 - After setting MCDU and ready to take off, the FCU not enter into managed mode only works when on the ground.
2 - In flight in the MCDU PERF page is in dispononivel.
3 - Alignment IRS takes 10min, Is there a way to be faster?
4 - APU also takes some time, no way to be faster?
5 - Detent position CL does not appear in ND N1.

Best Regards
Paulo

Hi Paulo

IRS needs in real that time, you can do a quick start by turning IR knob to NAV then Off and NAV again, than it will take around 30 sec. (RTFM ). The APU start will take that time too, there is no quick start for that.

Cheers
Stefan

[jeehell]

Hi,

Oh, and I thought there would only be a problem with the sound and not with the moving of the flaps lever also. Had a misunderstood. Is the new update already finished an ready for download? Then i will try this afternoon.

Sorry thought you had only the sound issue... What kind of SIOC Script do you use??


@Leonidas: fixes coming soon. One thing: the out of memory issue is strange and unknown to me yet. You get it every time you launch thes oftware??


@Storm24: please read the manual, and the FAQ.
1&2) Most probably you did not correctly fill the MCDU.
5) not very clear. Did you configure the THR LVRs in FMGS Config?

regards,
JL

[OmniAtlas]

Make sure you have adequate deadzone I'm your throttle levers or there will be errors when you try and use the fcu.

[tcane]

Hi JL,
no problem.
I use this following sioc-script wich i integrated with your sioc-creator.

Var 0000, Value 0


Var 0510, Link FSUIPC_OUT, Offset $0BDC, Length 4 // Flaps


Var 0512, Link IOCARD_ANALOGIC, Input 1, device 1, PosL 5, PosC 91, PosR 183 // Flaps Status 0-16383
{
L0 = V0512 * 64.247 // 16383/255
V0510 = L0
}


Maybe i find the fail in the script... I use Var 0000 (not over 0500) for the value??? But in your Version 32.2 without autoupdate this script runs perfect. Strange...

regards,
Florian

[jeehell]

@All: an update is available.


@Tcane: this script could not work correctly in B32.2. Maybe you had the correct flaps setting in your FS model, but the EWD most probably showed incorrect values for the flaps.

It is NECESSARY to use the flaps controls offered by my software. If you use an opencockpit axis, you can declare it in SIOC Creator in the MISC tab (axis 1 to 16), then you must configure the Axis in FMGS Config as you would with a regular joystick axis.

JL