A320 FMGS beta 26

[iwik]

Hi,
To go back just delete the Fsupic.dll from the modules folder should do it.
iccho : Have sent you a PM.
Les

[icchio]

hi guys, thank you again for the support, and thanks to Les for the file.
unfortunatelly i didn't solve my problem.
now my FSUIPC version is 4.6.
my problem is with the control surface.
FMGS configuration recognise my joystik but when i use it for move the airplane it doesn't work.
the cross on the PFD is moving with joystik but seems like FMGS don't speak with flight sim.
I'm using PA320 whit flight sim X
FSUIPC 4.669 and wideFS
someone have some ideas?
thank you again to for the amazing work.

[AirFan]

Hi icchio,

have you disabled all your control axis in FSX as well as FSUIPC? You dont need to assign any axis in FS nor FSUIPC since FMGS consideres the axes inputs directly from windows. What should work is the fsuipc version 4.60 from flightsim.com. I also use this unregistered fsuipc version without any trouble.

May I ask you something different: Have you bought a registration key for FSUIPC & widefs AFTER the release of V4.7? If that's the case, do these newer registration keys also work with the fsuipc version 4.60?? Did you try it? I would also like to get a key for 4.7 and wideFS... however, I am not sure if these newer keys also support any of the out-dated fsuipc versions?! For sure you can upgrade your version, but what about downgrading?

Cheers,
Rob

[jeehell]

Hi icchio,

Just to be sure, did you launch the AP/FB software? If yes, did you select the PA320 in the dropdown list?

JL

[icchio]

guys, thank you again.
I disabled all the axes from flight sim and FSUIPC had not axes configured.
but the joystik still doesn't work.
I also did what jeehell had suggested but nothing change.
the cross in the PFD is moving but the airplane don't move.
for now i have not a throttle and i'm using the keyboard directly connected whit flight sim.
can the problem come from that?

For Rob.
i have a registred version of FSUIPC 4.7.
for the downgreed i had changed just the dll file from 4.7 a 4.669 of FSUIPC module.
it seems like it works but until i didn't solve the problem with controls i can't be sure! =)

Giovanni

[Emmegi]

Hi again,
sorry for the delay but I was busy.
Relating to the frame rate, I did a test with the following settings: FPS set to unlimited, graphics custom, aircraft ultra-high, scenery high, weather high, traffic custom, view mode: just the front view (scenery without panel), FMGS active instruments: PFD and ND cpt, EWD, SD, MCDU cpt, FCU, STBY instruments. Result: the FS frame rate drops but its value is not stable in any condition. Frame rate range: (FS only) 20-30 FPS - (FS + FMGS) 5-15 FPS.
I'll do some other tests during my spare time.

Thanks

[jeehell]

Hello,

Icchio: you will definitely need the throttle axis, otherwise you wont be able to use the software. Not sure if it's why it's not moving at all the flight controls in the sim though. But using the keyboard to control the throttle is not possible. Now all cheap joysticks have a throttle axis...

Emmegi: if the frame rate is that low, it may be that the AP is getting flight data from FS with too muc delay, and so the AP/FBW does not like it. For your tests, I suggest you reduce the visual quality of FS to rule that out or confirm this fact.

Cheers,

JL

[Emmegi]

Hi everybody,
I did a test with all settings reduced to minimums and just FMGS PFD, ND, FCU and MCDU active, but I keep on having problems to make the AP system working properly. It's obvious that I'm doing something wrong. Hey guys, what do you mean with "disable all axes in FS"? Perhaps should I any changes in the FS control axes settings window? I feel like I would have lost some vital information...

Thanks
MG

[jeehell]

Hello,

You may have done all of this, but just might rin a bell:

-configure the joysticks and throttle with FMGS config
-in FS, go to Controls options and remove all assignments to joysticks and throttle
-launch AP/FBW, select the PA320 in the dropdown list, and click "load coefficient.
-Launch FMGS server and all other software (at least OVHD, FCU, PFD, ND,MCDU)
-On the OVHD:
-switch all korrys to ON position (if there is written OFF on it, click it)
-align the 3 IRS
-start the APU
-Now MCDU: follow the first flight in the guide.
-After that yyou should be set...

Regards,
JL

[icchio]

Hi Everybody,
i made all the step in the JL post but nothing changes.
disable all the controls from flight sim
start the AP/FBW and set the PA320....
Also the throttle doesn't work. same as for the joysticks, the blu bar on the EWD moves but the airplane doesn't move.
i also try with disable the FBW...nothing changes.

it seems like there is comunication beetwen the FSUIPC and FMGS because everything else works.
can the problem come from WideFS??
i really finished all my ideas.....

THANKS AGAIN!