Results 1 to 5 of 5
  1. #1
    1000+ Poster - Fantastic Contributor
    Join Date
    Nov 2008
    Location
    Europe
    Posts
    1,934
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Using flat cables

    I notice that many people that build their own projects use flat cable to connect electrical components due to that fact that it's neat and tidy and provides a great way to simply push in a connector and away you go.

    But looking at these flat cables, they look very delicate and was wondering just how you are meant to strip the ends without breaking the cable, surely the average pair of wire strippers is enough to shred the wire to pieces, so how is this done?

    Cheers,

    Alex
    GA or the Highway!

  2. #2
    500+ This must be a daytime job



    Join Date
    Jul 2013
    Posts
    917
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Using flat cables

    Alex

    If you are using flat cable to go from one multi pin connector to another, then these connectors are called IDC (insulation displacement connectors). The connector is in two pieces with V shaped sharp metal tags that cut into the insulation and make the connection. This is achieved by either using a special tool (readily available on Ebay or Rapid) - alternatively you could use a vice.

    If you are using flat cable to connect to various points then I would terminate into an IDC D Sub 25 way connector. You can then route the individual wires from this connector to the data points you require. Either way there is no stripping of individual wires within the flat cable.

    David

  3. Thanks caKus thanked for this post
  4. #3
    150+ Forum Groupie flatlandpilot's Avatar
    Join Date
    May 2009
    Location
    Netherlands, Zwolle
    Posts
    150
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Using flat cables

    I had my doubts with the way the connectors make contact
    with the wires, but I can say I never had problems with bad contacts.

    for pressing the connectors together I use a small bench-screw

    BTW it is possible to use 2 or 3 small flatcables
    to fill up the 25 of a connector. This can be very handy.
    When once you have tasted flight,
    you will forever walk the earth with your eyes turned skyward

  5. #4
    150+ Forum Groupie verticallimit's Avatar
    Join Date
    Apr 2009
    Location
    Denmark, Sinding
    Posts
    212
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Using flat cables

    I just made a part of my overhead panel, and i use flatcable, directly from the connector and to my contacts and LEDs.
    I use the panel for beta test and have moved and changed it several times and I must admit that flat cable is more rubust than it appears to be.
    I have made the wire ends long enough so that there will not be a jerk in the thin wire. The common negative wire is made of thicker and more rubust cord, and I've tied my ribbon cable down to it and this protects the flat cable against jerks
    Sincerely,

    Claus


  6. #5
    25+ Posting Member
    Join Date
    Apr 2009
    Location
    South Carolina
    Posts
    71
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Using flat cables

    There's wire strippers made for ribbon cable. You can usually pick them up where you buy the cable.
    John

Similar Threads

  1. connector cables for BU0836
    By brian95 in forum General Builder Questions All Aircraft Types
    Replies: 4
    Last Post: 08-30-2010, 07:34 PM
  2. USB hubs / extension cables
    By rottenlungs in forum Computer Hardware Setup
    Replies: 7
    Last Post: 08-27-2009, 04:14 AM
  3. Cables & wires 0,1mm
    By AchillesP in forum General Builder Questions All Aircraft Types
    Replies: 2
    Last Post: 01-06-2009, 11:11 AM
  4. projectors vs flat TV
    By Jackpilot in forum Cockpit Outside Visualization
    Replies: 35
    Last Post: 12-25-2008, 12:32 PM
  5. USB cables
    By wchambers in forum Phidgets & Cockpit Simulator Builder
    Replies: 2
    Last Post: 02-15-2005, 04:36 PM