Results 1 to 6 of 6

Thread: DXF files

  1. #1
    Have CNC-----will build.
    Join Date
    Oct 2009
    Location
    Leesburg, Florida
    Posts
    201
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    DXF files

    Per request, Matt Olieman has set up a new File in the File Library. It is under Miscellaneous and is call DXF FILES. This is going to be an excellent place to post all of the DXF files for special cutting on a CNC router. If you would rather post the G-Code files, I would imagine that would be ok also.
    Let's start sharing some of those awesome DXF files. I will begin uploading shortly.

  2. Thanks Joe Cygan, Matt Olieman thanked for this post
  3. #2
    Super Moderator
    Join Date
    May 2006
    Location
    Texas
    Posts
    616
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thumbs up Re: DXF files

    Super great idea!

  4. #3
    Have CNC-----will build.
    Join Date
    Oct 2009
    Location
    Leesburg, Florida
    Posts
    201
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: DXF files

    It might have been a good idea. I tried to upload a file of mine and it is too big to be accepted (gcode). The one I Tried to upload is a small one and has over 99,000 characters. The site is limited to 20,000 per upload.

  5. #4
    Super Moderator
    Join Date
    May 2006
    Location
    Texas
    Posts
    616
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: DXF files

    Just put the DXF. file on there and let the builder convert to G-code.

  6. #5
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    2,884
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: DXF files

    dxf is there now... Go for it!!!!

    Any other extensions needed let me know

  7. #6
    Have CNC-----will build.
    Join Date
    Oct 2009
    Location
    Leesburg, Florida
    Posts
    201
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: DXF files

    Sorry I could not get back with you.....got dropped and took over an hour o get back on

    Milt.

Similar Threads

  1. CNC files
    By sboons in forum CNC Discussion
    Replies: 2
    Last Post: 07-01-2010, 03:11 PM
  2. CAD Files
    By GDR in forum Where to Start Building a Home Cockpit
    Replies: 3
    Last Post: 02-11-2009, 10:56 PM
  3. CAD Files
    By ak49er in forum General Builder Questions All Aircraft Types
    Replies: 2
    Last Post: 03-01-2008, 08:39 PM
  4. DE1 and DE2 files
    By Elisio Cruz in forum PM General Q & A
    Replies: 5
    Last Post: 02-09-2006, 02:33 AM
  5. Where are the INI files?
    By RobertoR in forum FS2Phidget Users
    Replies: 9
    Last Post: 11-30-2004, 08:41 AM