Results 1 to 6 of 6
  1. #1
    Executive Assistant Geremy Britton's Avatar
    Join Date
    Jul 2007
    Location
    North,East England
    Posts
    1,447
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Urgent help on paint types.

    I have made a final decision for my overhead. For a while i've been deciding beween a 'printed' overhead and an engraved one. And i'm going for an engraved one. But my question is, before i send the panels off to be engraved.

    Has anyone had any experience with paint type pre-engraving?

    I'm hoping i can stick with my usual grey primer to give a couple of coats of that to my panels however would this be suitable to then be engraved on?

    Worst case scenerio would be i buy all the white plexi, paint it all and the grey primer flakes off or peels whilst been engraved.

    Can anyone give me reassurance that tyhis won't happen or perhaps give me any other warning signs i should look out for when engraving (to do with anything)

    Would maybe a sealable coat such as a clear laquer work? Or do i not need to bother at all wioth anything and it'll be ok?

    Please let me know of anything i should be aware of as i'm entering this next week. I've already got all the plans drawn for it, just need to get the plex and send it to the engraver.


    Please let me know your thoughts asap on this.


    Cheers!
    Geremy Britton
    Executive Assistant, MyCockpit Inc
    Head of GLB Flight Products
    www.geremy.co.uk

  2. #2
    300+ Forum Addict phil744's Avatar
    Join Date
    Aug 2007
    Location
    Lancashire, england
    Posts
    336
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Just make sure your panels are sanded (keyed) before paint, they should have a matt finish on all sides, also it is wise to wipe them down before paint with alcohol soaked cloth to remove any greace, then use tack cloth to remove dust. I wear latex gloves when doing mine.

    Try to avoid having sharp edges on the panels, they will be easy to chip, but good sanding will avoid this, but before you go anywhere do a test panel first and throw it around and try and scratch it yourself, this will give you more confidence.

  3. Thanks fweinrebe thanked for this post
  4. #3
    Executive Assistant Geremy Britton's Avatar
    Join Date
    Jul 2007
    Location
    North,East England
    Posts
    1,447
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Seems pretty straight forward then in terms of precaution before engraving. Any particular recommendation for the "alcohol soaked cloth" ? I like to save my beer for the flight ideally - And *i'll* do the drinking not the panels LOL

    Thanks for the reply Phil
    Geremy Britton
    Executive Assistant, MyCockpit Inc
    Head of GLB Flight Products
    www.geremy.co.uk

  5. #4
    Heli Builder
    Join Date
    May 2008
    Location
    Earth
    Posts
    288
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I recently made panels using white Perspex, sanded them with 1200 grain and then gave them a grey primer. After that a black matt coat until I couldn't see the sunlight going through holding it up against the sun. Then used a Laser CNC to do the engraving. I am happy with it and awaits fitting of the switches and LED's for the backlighting.

    I am considering a clear laquer coating because I'm afraid the paint might come off with time if the panel is handled a lot. Will do an experiment first.

    Phil thanks for the tip about the sharp edges.
    Fritz -> Helicopter Cockpit Builder
    (FSX | TH2Go | Arduino | Air Manager Avionics | CNC)

  6. #5
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Be careful spraying a lacquer coat on the primer. If it's enamel you will ruin the finish. It will orange peel and destroy the primer.

    You can spray enamel over lacquer, but not lacquer over enamel.

    The best paint I've found for panels is Dupli-Color brand New Ford Gray for engines. It's a ceramic based hi-temp paint that sprays exceptionally well, and levels itself with a very smooth finish and dries fast. It's also very tough without being brittle after curing.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  7. Thanks fweinrebe thanked for this post
  8. #6
    300+ Forum Addict phil744's Avatar
    Join Date
    Aug 2007
    Location
    Lancashire, england
    Posts
    336
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Its always wise to stick with the same type of paint, when you spray the clear coat dont apply it to thick and make sure the panel is laid flat, what can happen is the clear coat will soften the paint that has been engraved and it can run and ruin the engraving.

Similar Threads

  1. NEED URGENT HELP! 180DEG FOV
    By Nasser in forum Cockpit Outside Visualization
    Replies: 4
    Last Post: 09-16-2010, 06:38 AM
  2. Urgent for Ian P.Sissons
    By Carlos Corona in forum General Builder Questions All Aircraft Types
    Replies: 2
    Last Post: 01-22-2009, 02:23 AM
  3. Monitor sizes/types?
    By manhattan in forum Computer Hardware Setup
    Replies: 2
    Last Post: 12-12-2007, 11:23 AM
  4. Urgent Matter!
    By dodiano in forum General Builder Questions All Aircraft Types
    Replies: 0
    Last Post: 05-26-2007, 10:07 PM