Results 1 to 7 of 7
  1. #1
    150+ Forum Groupie Suggy's Avatar
    Join Date
    Oct 2005
    Location
    Hull, England
    Posts
    151
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thrust Lever Markings Question

    Hi!
    I have a 'strange' question. I am about to fix my thrust lever markings on my throttle from FDS. What I am not too sure about is exactly where they are located in reference to the thrust levers. TOGA, FLX MCT and CL have small 'arrows' indicating if the throttle is in that position. But where exactly does it match up on the thrust lever?

    I hope ypu understand my question

    Al the best,

    Darren

  2. #2
    MyCockpit Support Staff dodiano's Avatar
    Join Date
    Oct 2005
    Location
    El Salvador
    Posts
    930
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hey Darren,

    What you mean?? Like what percentage of EPR or N1 is in regard to the lever position?? Don´t quite understand the question??

    Regards,

    Roberto

  3. #3
    150+ Forum Groupie Suggy's Avatar
    Join Date
    Oct 2005
    Location
    Hull, England
    Posts
    151
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    It's difficult to explain without a photo. I am talking about the actual thrust lever housing. It has markings which are TOGA, FLX MCT, CL, 0 and REV. In the middle between the two thrust levers there are markings ranging from 0 to 45.

    Is this clearer?

    Regards,

    Darren

  4. #4
    300+ Forum Addict


    brianwilliamson's Avatar
    Join Date
    Oct 2005
    Location
    Gold Coast-AUSTRALIA
    Posts
    455
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Gooday Darren, Try this site, should help. I think that is what you are looking for,
    Regards..................Brian W.
    http://www.simpit.de/a320dim/page_05.htm

  5. #5
    150+ Forum Groupie Suggy's Avatar
    Join Date
    Oct 2005
    Location
    Hull, England
    Posts
    151
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Perfect! Thank you. I never realised that there was a line drawn on the side of the thrust lever to show its position.
    Once again, thank you.
    Regards,
    Darren

  6. #6
    MyCockpit Support Staff dodiano's Avatar
    Join Date
    Oct 2005
    Location
    El Salvador
    Posts
    930
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Oh Ok now I get you!! Oh well I´m glad Brian was able to help!!! Thanks Brian.

    Regards,

    Roberto

  7. #7
    150+ Forum Groupie Suggy's Avatar
    Join Date
    Oct 2005
    Location
    Hull, England
    Posts
    151
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks Roberto

    Darren

Similar Threads

  1. Thrust lever pots and MSFS
    By mach7 in forum MyCockpit Support:
    Replies: 0
    Last Post: 05-02-2009, 10:36 AM
  2. Is it a throttle, power lever or thrust lever?
    By fweinrebe in forum Pilots Lounge - Let your Hair down
    Replies: 2
    Last Post: 03-21-2009, 09:50 AM
  3. thrust lever position in B737
    By michelmvd in forum PM General Q & A
    Replies: 6
    Last Post: 08-12-2008, 09:54 AM
  4. 744 Thrust lever dimensions? Anyone? Anyone?
    By GSwindle in forum Cockpit Parts and Motion Platforms
    Replies: 2
    Last Post: 04-21-2007, 10:22 PM