Results 1 to 5 of 5
  1. #1
    75+ Posting Member
    Join Date
    Sep 2007
    Location
    Perth WA
    Posts
    102
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Wiring setup for overhead

    Hey guys,

    I was just wandering if anyone can share some opinions on the best way to wire up my overhead, perhaps a tutorial.

    here are my thoughts, im going to use Phidget led64 for the leds,
    and FDT for interface. I was thinking of using Phidget 0/16/16 interface kit however FDT looks alot more easier to configure.

    im not too sure on how exactly to wire the switches,pots etc.

    most of the switches are these type, 2position and 3 position



    i was thinking of joining all the centre poles, PWR, in a serial kinda like a common wire and then each other pole to a input on the FDT board.

    Not sure if this is the correct method ?

    Also is there any tricks to connecting pots and rotary switches up.

    Any sugestons, photos of your own setup or help would be greatly appreciated.
    Last edited by ozziesim; 01-02-2008 at 06:37 AM. Reason: forgot something

  2. #2
    500+ This must be a daytime job
    Join Date
    Nov 2005
    Location
    rotterdam, the Netherlands, Europe
    Posts
    804
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    the fdt boards can be wired one on one (ground and positive for each switch) OR with a common ground. You can use one common ground for all switches. Meaning you will wire the ground wire from switch to switch to every center pin of your switches and then wire it to a single ground pin on the FDT board (bottom row of pins)
    And then wire the trigger wires to the individual inputs (top row of pins)

    I prefer one on one wiring, because when the common ground failes you loose alot of switches at once with a common ground. Hard to trouble shoot.

    But both methods are possible.

    Stef


    .
    www.boeing737ng.com
    ___________________________
    The Dutch 737 Simulator Project

  3. #3
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Well as Stef has pointed out there is a down side to common ground, but....The positive side is if you are doing like a 737 OH.. You can eliminate over 70 wires from your OH to the interface card.... I like less wires!
    Bob Reed

  4. #4
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    2,884
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    As you can see in the couple of replies, there are choices and opinions Of course the choice is yours...

    Did you do a search (here) on overhead wiring or Phidgets, FDT, etc. wiring? It seems there are diagrams here.... somewhere

  5. #5
    500+ This must be a daytime job
    Join Date
    Nov 2005
    Location
    rotterdam, the Netherlands, Europe
    Posts
    804
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    You could also make a compromise and use a common ground for one section. For example in the way the panels would be in real. So 1 common ground for the fuel pumps, one common ground wire for the generators, etc.

    The old phidget led64 board had to be interfaced one on one, the new one is different i think.

    The FDT output board uses 1 common for 8 led's, but the commoned group is spread over the side of the board and in my opinion it makes it look like a mess when using commons with this board.

    The FDT forum has great tutorials on using commons.

    Stef
    www.boeing737ng.com
    ___________________________
    The Dutch 737 Simulator Project

Similar Threads

  1. FSX system setup for full 737 cockpit setup
    By BBJ737 in forum Computer Hardware Setup
    Replies: 0
    Last Post: 02-20-2011, 12:25 AM
  2. help ref wiring
    By BishBash in forum I/O Interfacing and Hardware
    Replies: 26
    Last Post: 11-03-2010, 07:06 PM
  3. Wiring up an overhead
    By Drewsta in forum I/O Interfacing and Hardware
    Replies: 4
    Last Post: 11-27-2009, 03:29 PM
  4. wiring
    By phil. in forum OpenCockpits General Discussion
    Replies: 3
    Last Post: 09-15-2008, 03:38 AM