Results 1 to 10 of 36
Thread: Autothrotlle and PM-MCP
-
12-03-2007, 01:48 PM #1
- Join Date
- Dec 2006
- Location
- Kavala, Greece
- Posts
- 60
Autothrotlle and PM-MCP
Hello
I have make some test with the autothrottle and i have notice a strange behavior of the lever when is moving.
In flight engage the A/T switch
Lets say the Offset $088C (Is the left lever) takes a value 11,500 , THEN starting slowly decent until 6.000 or 7.000 value (the decent time is 5-7 sec) and THEN JUMPS in 1 second to a value close to 11,500.
And this continues all the time.
THE LEVER IS NOT STABLE.
the lever goes up and down.
Now, if i don`t use the PM-MCP and use the default MCP from the fs9 or the fsx everything working perfect.
i use the DC motor from OpenCockpit with SIOC code.
I don`t know if i explain my problem good.
I am not so good in English.
Regards
Lambis
-
12-09-2007, 12:10 PM #2
- Join Date
- Dec 2006
- Location
- Kavala, Greece
- Posts
- 60
Hi Again
Only me have this Problem?
The Throttles are not stable when the airplane is in climb take-off mode especially when i use V/S
The lever are slowly down and then jump fast up again.
In the CRUISE mode is better.
With the FLCH there is not exist this problem.
When i remove the Project magenta MCP and use the default MCP of fs everything are stable.
Is something wrong communicate the fs with mcp?
Need to change something in FSUIPC?
Same behavior and with FS9 and with the Fsx.
With and without SIOC.
Regards
Lambis
-
12-09-2007, 11:55 PM #3
Hello Lambis
Yes i have a simular problem. What kind Of MCP are you using with PM systems? I have been using CP Flight and PM MCP with FSX.
I have been trying to figure out why it does this without any success so far.James Twomey
-
12-10-2007, 01:43 PM #4
- Join Date
- Dec 2006
- Location
- Kavala, Greece
- Posts
- 60
Hi James
I use the real B777 MCP panel with SIOC code with the cards from Open cockpits and Magenta MCP software and fsx.
But i think the problem is in the MCP software becuase when i fly with the default A/P of fsx and don`t use the Magenta MCP the lever are very very stable.
Same and in the fs9.
When run again the Magenta MCP the lever starting the slowly down and the fast up movement.
Is very strange why other people never report this behavior or never notice this.
Can report the other simmers this behavior of the A/T.
Is a bug or is something that must check in the ini files.
Regards
Lambis
-
12-11-2007, 08:04 AM #5
- Join Date
- Jun 2007
- Location
- Ireland
- Posts
- 105
Hi,
I don't know if it is related but the airbus FCU A/T is very quirky like this also.
It is especially unstable on take-off and climb - takes far too long for appropriate take-off thrust to be selected (never mind the normal spool-up delay) and the speed is often allowed to go a good 20 knots above or below the selected speed before the A/T "wakes-up" and corrects the thrust.
I often see the little bug on the N1 thrust dial move up and down very fast as if the A/T is getting confused as to what the correct commanded thrust should be.
Also, the flight director often commands extreme pitch angles during take-off / climb-out phase.
So, these kind of PM bugs seem to be very common.
regards,
Ryan.
-
01-19-2008, 03:42 PM #6
- Join Date
- Dec 2006
- Location
- Kavala, Greece
- Posts
- 60
Hello
Can Jonathan or Thomas tell us why this happen?
Is a bug of A/T?
Enrico knows this problem?
Regards
Lambis
-
01-19-2008, 05:35 PM #7
- Join Date
- Jan 2006
- Location
- UK / Germany
- Posts
- 174
Autothrottle and PM-MCP
>Can Jonathan or Thomas tell us why this happen?
Is a bug of A/T? Enrico knows this problem?
Hi
I would start looking at your MCP cycle time - the recommended setting is between 50-70 to be set in the MCP ini *but* this is entirely system dependent. Too high a number and you might miss bits of information, too low and the same in reverse. There is an optimal and you should look at this per system. I have a setting of 30ms here in the simulator. I have 100% rock steady AT ops. Speed is within + / - 3kts whilst AP and AT are engaged. I do not use V/S as a level chance very much but have not noticed anything recently with that but will re-check. The other factor in this (and related to the above) is the network speed / and or errors of course. Make sure your FS framerate is not something that can not be sustained leaving no time for network / MCP.
Further to this, check your flight model, make sure it is balanced correctly (but from what people have said it seems this would not be the issue here). Do your tests with no wind or adverse weather - for obvious reasons.
Then I would move to the CDU / MAINT / AT pages. Here you can alter the effectiveness of the AT - norm is 100 - and if you mess around with this go gently - you will have to perfrom many tests to see if / what is effecting things. Unfortunately there is no documentation for these settings. I'm sorry about that, but that is the way that part is. Generally it should not need touching. I think if you play with values up to 120 // 140% you might see the effects. Again, this I would say is secondary, and should not be required - don't open a can of worms for yourselves with this unless you are 100% sure of the first part being correct. I think if you are see big changes or "hunting" of the AT it is more likely to be network or cycle time related.
Regards
Jonathan Richardson
Regards
Lambis[/QUOTE]Jonathan Richardson
-
01-20-2008, 03:43 AM #8
- Join Date
- Dec 2006
- Location
- Kavala, Greece
- Posts
- 60
Hi Jonathan
Today morning i have make a test and i change the values in the MCP cycle time.
I give values from 30 to 70 and the bevavior of the A/T is the same.
I make test without CDU.
The frames or the fs are up to 40.
I use the FS and the MCP in the same computer (no network).
I use different aircrafts.
All they have same behaviour. The lever go up and down.
If I stop the Project magenta MCP and use the defualt MCP of the fs the A/T is stable.
Something is bother the A/T.
Can i send you any log file maybe you undestand what is going wrong?
From FSUIPC? from MCP? My MCP.ini ?
Regards
Lambis
-
01-20-2008, 04:45 AM #9
- Join Date
- Dec 2006
- Location
- Ireland
- Posts
- 255
-
01-20-2008, 05:55 AM #10
Prettys Womans from your city for night
A320 Sound Files Missing