Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Panel Building

  1. #1
    25+ Posting Member
    Join Date
    Mar 2007
    Location
    South Africa
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Panel Building

    Guys I would really appreciate it if you could shed some light on homebuilt panels.My method I am planning on making my panels will be similar to the method this guy has used http://ourworld.cs.com/f16simulator/index.html.
    Apparently the backlighting is quite good.
    I would really like to know what you guys think of this I have seen it been used extensively by homecockpit builders, OR do you think I should just buy some milky white plexi,spray paint it (in my case Learjet 45 MIP color) and take it to a engraving shop.

    Thanks guys for your comments !

  2. #2
    25+ Posting Member
    Join Date
    Mar 2007
    Location
    South Africa
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site


  3. #3
    2000+ Poster - Never Leaves the Sim Trevor Hale's Avatar
    Join Date
    Nov 2005
    Location
    Ontario, Canada
    Posts
    2,223
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hey Buddy,

    Not to toot my own horn, but I think I pioneered this process years ago. All of my panels are made in this manor. I use a clear spray adhesive and attach the glossy photo paper directly to the Plexi, then drill my holes right through the paper.

    You need to get the high quality photo paper otherwise the back lighting will bleed through the black parts of the panel.

    It is a great process, and to tell you the truth if you were in my cockpit, I don't think you would notice a difference. The only issue (compromise you need to make) is that you can't have any other color of panel other then Black backgrounds. I print Blue, red, etc. for gear lights and stuff, but You can't have that Boeing Grey, unless your willing to put black underneath it.

    Best regards,

    Trev
    ________________________
    Trevor Hale

  4. #4
    25+ Posting Member
    Join Date
    Mar 2007
    Location
    South Africa
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Trevor thanks

    This information is very encouraging indeed.I wonder how I will get that Grey color that the Learjet MIP has.How effective is that method you (Trevor) mentioned in the previous post about first putting black underneath and then the color you want.How would you go about doing this?

    Thanks, this is truly a great forum !
    I will have some pics up soon !!!

  5. #5
    2000+ Poster - Never Leaves the Sim Trevor Hale's Avatar
    Join Date
    Nov 2005
    Location
    Ontario, Canada
    Posts
    2,223
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Well, it is tricky, and I will explain briefly why.

    You need to print the panel in Black/White, then in Grey/White. Next you need to attach the black behind the Grey.. So that the text, and lines all line up perfectly.. This is very hard indeed, especially with spray adhesive, then once you have the two stuck together then you need to use the adhesive to attach it to the plexi.

    But with the small text any little variation will appear like the text is blurred. you will have to test it to see what I mean.

    Does that make sense?


    Trev
    ________________________
    Trevor Hale

  6. #6
    25+ Posting Member
    Join Date
    Mar 2007
    Location
    South Africa
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Trevor thanks for that explanation.I understand completely.
    I'm gonna have to give it a try although I wish I could just print 1 layer of grey (MIP Color) on the paper and then just stick it to the plexi but I guess that way would probably pass too much light through the grey color and would then defeat the purpose.I'm gonna try some experiments and will post my results.I assume that the engraving method would probably work best although it could be costly.

  7. #7
    2000+ Poster - Never Leaves the Sim Trevor Hale's Avatar
    Join Date
    Nov 2005
    Location
    Ontario, Canada
    Posts
    2,223
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    You got it 100% too much bleed through on the Grey color. As for the Engraving. If you can find someone to do it for you, it would be costly, but the biggest issue, is the small font of the text during engraving is tricky.

    Let us know how it works out.

    Trev
    ________________________
    Trevor Hale

  8. #8
    25+ Posting Member
    Join Date
    Mar 2007
    Location
    South Africa
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Trevor I noticed my cars panels at night,it looks fantastic.I wonder what technique vehicle manufacturers use to light up the panels inside because it looks great !!!!.It seems to be normal plastic with printing on.

  9. #9
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I built one, and only one pael for my Boeing stall warning indicator.

    I used two sheets of plexi-glass and a thin layer of styreen. I drew up the panel on the computer and printed three copies. I sandwiched those three together and applied it to the top piece.

    The bottom (back) piece was routed for the 12VDC grain-of-wheat bulbs wired in parallel and sealed with caulk.

    It works just like a commercial lightplate, but was a lot of work that I probaby won't do again.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  10. #10
    25+ Posting Member
    Join Date
    Mar 2007
    Location
    South Africa
    Posts
    38
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks I am going to have a go at it.
    I will see which method works best for me which would probably be a trial an error process.

    Thanks for your input !

Page 1 of 2 12 LastLast

Similar Threads

  1. Panel building, focussed on dimensions: *TUTORIAL* uploaded
    By Hessel Oosten in forum Westozy's Mechanical Engineering
    Replies: 9
    Last Post: 01-30-2011, 10:54 AM
  2. Cockpit Building, nah......it's all about Airport Building!
    By CessnaGuy in forum Pilots Lounge - Let your Hair down
    Replies: 3
    Last Post: 07-08-2010, 06:43 AM
  3. Saitek Multi Panel and Switch panel
    By baw536 in forum I/O Interfacing and Hardware
    Replies: 2
    Last Post: 12-28-2009, 05:31 PM
  4. Building a 737
    By IVA739 in forum Where to Start Building a Home Cockpit
    Replies: 15
    Last Post: 09-24-2009, 03:54 PM
  5. Building an MCP?
    By Westozy in forum Computer Hardware Setup
    Replies: 0
    Last Post: 03-05-2007, 01:28 AM