Results 1 to 5 of 5
  1. #1
    75+ Posting Member flightdeck's Avatar
    Join Date
    May 2007
    Location
    LOWW
    Posts
    149
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Question Missing Message in CDU Scratchboard

    I've tested several times my Engravity CDU with PM's CDU software. A major problem popped up: "Messages" are not displayed in the scratchboard as expected, I have to recall them via menue button and then in ">messages". "Show messages" is enabled in the CDU menue, same happens in the RCDU of course.

    Did anyone have a similar problem and alraedy a solution? I wrote to PM support, but no reaction from their side until now ...
    Thanks in advance
    René

  2. #2
    10+ Posting Member
    Join Date
    Jan 2007
    Location
    USA
    Posts
    11
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I have an engravity CDU and that I have always had to go to a separate message page to read messages (never in the scratch pad). I think this is a logic issue that needs to be resolved by the PM folks.

    CJ

  3. #3
    150+ Forum Groupie
    Join Date
    Sep 2007
    Location
    Northern Italy
    Posts
    160
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Boeing ... and how about the missing messages ?

    I guess it's not all.

    Did you ever notice there are quite a lot of missing messages from the CDU ?

    I couldn't realize it until I examined the complete message set of which a CDU is capable, taken from Bill Bulfer's Guide (The 737 FMC Guide).

    One for all: "RESET MCP ALT" when you get close to TOD in VNAV mode and you have forgotten to lower the ALTITUDE value, to allow the MCP to begin descending ...

    Cheers,

    Eu

  4. #4
    500+ This must be a daytime job
    Join Date
    Nov 2005
    Location
    rotterdam, the Netherlands, Europe
    Posts
    804
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    To get things straight:

    You are missing that message in the PM software CDU, right ?

    Stef
    www.boeing737ng.com
    ___________________________
    The Dutch 737 Simulator Project

  5. #5
    75+ Posting Member flightdeck's Avatar
    Join Date
    May 2007
    Location
    LOWW
    Posts
    149
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    You are missing that message in the PM software CDU, right ?
    RIGHT, it is PM software related!
    Enrico mailed me, that he is aware of it and added it to the "to do" list!
    René

Similar Threads

  1. MTR Button and FMC Message light
    By captdave in forum PM Boeing GC
    Replies: 2
    Last Post: 12-05-2010, 07:30 AM
  2. What does this message mean???
    By flyboy01 in forum PM Boeing FMC/CDU
    Replies: 1
    Last Post: 05-27-2009, 09:47 AM
  3. what is this error message
    By djcevera20 in forum I/O Interfacing Hardware and Software
    Replies: 0
    Last Post: 05-16-2009, 04:21 PM
  4. Message From The Vice President
    By Trevor Hale in forum MyCockpit News and Announcements
    Replies: 0
    Last Post: 04-23-2008, 08:42 AM