Results 1 to 6 of 6
-
10-31-2008, 01:05 AM #1
Please Help!! 7 Seg Displays with OC Displays card
I have assembled 2 of the 4 display II cards i ordered in kit form from OC along with the master and expansion card..
The master card an expansion card which i assembled are working perfectly. Power to MC is through a seperate PSU constant 5v.
I decided to test the displays card connected to a 3 display PCB from OC. Unfortunately the top right segment and the bottom left segment dont light up with one of the cards and also not all grounds seem to work either.
Out of curiosity i assembeled another displays card and the same thing happend. either it wont work altogether or only 5 segments light up showing a 5 on the display. when i run the counter in controller program i can see its working but without those two segements. I have checked jumper settings and controlador.ini etc.
I have thoroughly checked the solders and IC seating etc several times and also assembled another 3 display PCB to rule out any faults. Changed cables and everything i could think off.
I have noticed on some forums that others have had trouble with this but cant find any resolutions.
Is someone able to give some guidance to identify the cause or fault??
-
10-31-2008, 05:52 AM #2
- Join Date
- Aug 2008
- Location
- UK
- Posts
- 72
Seems like you have done a lot to try and get to the bottom of this. I don't know the answer but you could try manually 'flashing' the 7seg displays out of the holder to rule out a duff batch of displays. Don't forget to include an appropriate resistor in there !
Skywatch
-
10-31-2008, 06:28 AM #3
- Join Date
- Jun 2008
- Location
- Stafford, UK
- Posts
- 161
Are you using common cathode 7 seg displays? Common anode ones wont work and might be the cause of the problem.
-
10-31-2008, 09:37 AM #4
Thanks for your answers.. Yes these are common cathode displays and i have 62 of them all ordered from OC. When i flash them all segments work ok on all the pcb's i've assembled.. I ran a check on the mounting again but to no avail .. Im starting to think whether its a bad batch.. now i don't get anything at all with the first couple of gnd's.. but i get some segments that appear around pins 9 -16.. No response from controller program.. I used another master card and there's still no difference.
Would it matter where the IC's are placed ? I don't mean the position of them but whether all the 16 pin ones are the same ? would anyone be kind to share a closeup photo of their OC Displays II card? That would be extremely helpful.
-
10-31-2008, 03:03 PM #5
- Join Date
- Jan 2007
- Location
- NEW ZEALAND
- Posts
- 908
Hi,
If you have tested all the 7 segment display bds by flashing them independantly of thr display II pcb.Then you can rule out faulty displays/Pcb.
There are 16 display outputs per bd.Did you try a 7 seg display bd on all
16 outputs to see if they give the same fault on all 16 outputs?.
As these are a multiplexed disply system,the only thing that is unique for each display is the Common Cathode.All the same segments are joined together.If these are alright then it leaves only decoding.
Please be a bit more descriptive as to where and what chips you are referring to.I would have thought if the kit was bought from o/c then they would have only supplied the correct brand of chips if this was important.
How about posting a pic of the 7 seg pcb and display II card running.
Give aclose up of the Display II board.Iv completed my one but have not tested it yet.
rgds
Les
-
10-31-2008, 06:09 PM #6
- Join Date
- Oct 2006
- Location
- Perth, Australia
- Posts
- 263
Have u tried turning the power onto the cards first before turning the pc on?
MichaelA320 Home Simulator LHA435
- P3dv4.5 - i7 - GTX970 - Fly Elise - ASN - Black Marble
Similar Threads
-
Opencockpits USBLCD Card Displays
By Boeing 747 Flyer in forum Cockpit Parts and Motion PlatformsReplies: 14Last Post: 10-01-2010, 02:51 AM -
ND Displays
By stepbk in forum General Builder Questions All Aircraft TypesReplies: 0Last Post: 04-15-2010, 12:15 PM -
FSLCD with OC LCD DISPLAYS CARD
By shafian in forum OpenCockpits General DiscussionReplies: 3Last Post: 08-29-2009, 09:46 AM -
Displays card.
By Jake 747 400 in forum OpenCockpits General DiscussionReplies: 3Last Post: 02-26-2009, 06:42 PM -
Moving PM Displays
By B738 in forum PM Boeing GCReplies: 3Last Post: 08-10-2007, 05:59 PM
Enter and win!
JeeHell FMGS on a remote Computer