A320 FMGS B31

[jeehell]

@StefanGr: I'll look at that, I do not know where it comes from, this is not lag at all.

@Stefan/Miatanet: you simply have to start FS BEFORE the FMGS...

JL

[Miatanet]

@StefanGr: I'll look at that, I do not know where it comes from, this is not lag at all.

@Stefan/Miatanet: you simply have to start FS BEFORE the FMGS...

JL

works!!!


Best regards
Stefan

[tote_320]

just installed from scratch 32.4...previously uninstalled aircraft from fsx...so everything is clean and new.
something must be off in the new .air file or FBW : it's impossible to control the aircraft in pitch which suddenly "jumps" up or down on small stick inputs...also the AP is not able to control the pitch.
am i the only one with this?
cheers
fil

Same here
I put the correct airfile and the problem still there, it improves a little bit but its pitching up and down all the way, when i reach cruise altitude it levels, but then it starts pitching 6,000 or 8000,ft per min, up and down.

Dont know whats going on, also after that the MCDU and the FCU was not responding.

[GlobalGentleman]

I've been experiencing the same situation here....and that's not from a fully clean install, just using the updater. The new air file I downloaded separately and inserted manually.

During all stages of flight I'm getting oscillations of +25deg up to -15deg down on pfd. At first I thought it was just my poor W&B management skills that were to blame lol

I'll give any new update a try but, sorry to say, for the moment it's relatively grounded.

Cheers,
Alan

[Airmichel]

Hi JL,

after a long overhead and pedestal construction I'm back. Your software gets better and better, incredibly. It makes a lot of fun to fly. Unfortunately I have after a complete new software installation small problems. On the nd waypoints, vors, ndbs and airports are not displayed, only the constraints are displayed. A new installation of Navdatapro file on all PCs has not helped. With version B32.2 everything was good. The second problem is, when I turn on the Seatbelt Signe the Fault LED flashes on the master switch. The same thing happens, when I turn the Alt knob on the FCU. In SIOC monitor the effect is not present, only when I started the cockpit software. Is it possible that is a fault in the cockpit software? I checked my Cable , Leds and Switches, but i found no mistakes. Thanks again for the great cockpit software.

best regards to Nice

Micha

[tcane]

Hi Jl/ Guys,
in a short time,I get a used USB radio from cockpitsonic. Does jeheel support this hardware?
Regards
Florian

[asessa]

Hi Jl/ Guys,
in a short time,I get a used USB radio from cockpitsonic. Does jeheel support this hardware?
Regards
Florian

Yes, it works.
I've the same RMP


@JL : do you have any solution for backlight ?

[filippoporcari]

for the guys experiencing AP issues, as i reported a clean installation of 32.4 (repeated 2 times in my case) solved everything in my setup.
cheers
fil

[jeehell]

Hi,

@Alan,@tote_A320: make sure:
-you closed FSX or P3D
- install the software from B32.4 installer (check above posts for the link)
- make sure W/B are correct (not too heavy, not too light, CG at about 25 to 30%)
- your FS framerate must OVER 25fps. This is a NO GO if you are at anytime below that.


@Micha: you maybe do not have the latest version. You must use the latest version, check the B32.4 installer (link in previous posts ..).

@Asessa: I did not have time to look again at that small issues sorry.


JL

[asessa]

@Asessa: I did not have time to look again at that small issues sorry.


JL

Hi JL, i think it isn't a small issue.
With old version (B30) was ok. So i think it is a big issue of new version.