Results 21 to 30 of 34
Thread: eng start with pm sys
-
11-11-2008, 12:42 PM #21
I am using the latest FSUIPC with FS9.
I am controlling the engine start switches now right from the overhead image on the Pmsystems screen. (No hardware yet)
No other software running on that machine except for the CDU.
My cutoff switches are curently disabled in PMsystems, and are going to be connected directly to FSUIPC.
But for now, just using the graphic to ensure the cutoff switches are in the fuel on position.
Trev
________________________
Trevor Hale
-
11-11-2008, 12:52 PM #22
- Join Date
- Dec 2006
- Location
- Ireland
- Posts
- 255
-
11-11-2008, 12:53 PM #23
- Join Date
- Dec 2006
- Location
- Ireland
- Posts
- 255
I forgot
What are the Offsets you use for the CUTOFF and what are the Values you write to to Fire?Regards
Thomas
-
11-11-2008, 01:05 PM #24
Ohhh, actually no.. I don't have that one selected.. Gosh my brain is fried.
the cutoff switches aren't the issue though, as I can't even get engine #2 to start cranking...
If it was a cutoff switch issue, the engine would at least crank over, but not fire.
I can't get it even to start spooling up.
Trev________________________
Trevor Hale
-
11-11-2008, 01:05 PM #25
-
11-11-2008, 01:16 PM #26
- Join Date
- Dec 2006
- Location
- Ireland
- Posts
- 255
The Bleed-2 shows pressure? (Isolation Valve is in OPEN or AUTO position?)
Regards
Thomas
-
11-11-2008, 01:18 PM #27
Yup sure does, I have even tried dual bleed. I have put the packs in all positions, like I said i can get engine 1 to crank no problem. but engine 2 will not crank at all.
I have tried every switch position imaginable, on Auto, On, or off.
Even moving the ign switch from Right, to Both and to Left, still seems to have no effect on engine #2.
But when I go into Flight sim. Ctrl + E always cranks and fires engine #2 just fine.
Trev________________________
Trevor Hale
-
11-11-2008, 01:23 PM #28
- Join Date
- Dec 2006
- Location
- Ireland
- Posts
- 255
Make sure there is nothing in FSUIPC defined for the Engine Starter (from old days may be).
Does the Start switch stays in Start position then or does it switches back to OFF by itself ?Regards
Thomas
-
11-11-2008, 01:27 PM #29
LOL, I checked that already.. FSUIPC is clear with no definitions in it at all at this point.
when I move the start switch on the overhead to GND, it just stays there for ever and ever... until I move it to a different position.
But no engine crank.________________________
Trevor Hale
-
11-11-2008, 01:31 PM #30
- Join Date
- Dec 2006
- Location
- Ireland
- Posts
- 255
When you did that (ENG-2 in GND) just press on pmSystems-PC CTRL + A and send me the sysana.txt file from pmSystems main folder.
Regards
Thomas
Similar Threads
-
FSX won't start
By PDT 200 in forum General Microsoft Flight Simulator 10 (FSX)Replies: 9Last Post: 02-26-2009, 03:48 PM -
737 Start Up
By mounty in forum General Builder Questions All Aircraft TypesReplies: 4Last Post: 01-16-2009, 09:48 PM -
Where to start
By craiso in forum I/O Interfacing Hardware and SoftwareReplies: 10Last Post: 10-28-2008, 05:03 PM -
where dio i start
By seristee in forum General Builder Questions All Aircraft TypesReplies: 4Last Post: 06-27-2008, 02:39 PM -
How to start?
By RobertoR in forum FS2Phidget UsersReplies: 5Last Post: 11-24-2004, 11:28 PM
Beautiful Womans in your town for night
B_34 TOGA takeoff