Results 241 to 250 of 737
Thread: Progamming help with FSBus dll
-
01-24-2010, 04:28 AM #241
Re: Progamming help with FSBus dll
The new board is working perfectly, but it's the old board suddenly doesn't work.
-
01-24-2010, 04:31 AM #242
- Join Date
- Feb 2008
- Location
- Krefeld, Germany
- Posts
- 318
Re: Progamming help with FSBus dll
ah, ok.
How do you connect the old board to the setup, is it on the same cable like the new one.
or has it his own connector on the COM Board?
Stefan
-
01-24-2010, 04:34 AM #243
Re: Progamming help with FSBus dll
The new board has it's own cable to the com board. The old DIO has a shared cable to the Servo board (you probably remember the problems with having the change the fuse bits on the servo board)
I was moving the cables (10pin) around to test a couple of things that weren't working on the new board and then the old one stopped.
Oh, I didn't change the fuse bits on the DIO, only the servo board
-
01-24-2010, 04:43 AM #244
- Join Date
- Feb 2008
- Location
- Krefeld, Germany
- Posts
- 318
Re: Progamming help with FSBus dll
That all sound realy strange.
Do all parts of the board donīt work or only some parts?
Can you measure the 5V power on the Controller of the old board?
Stefan
-
01-24-2010, 06:02 AM #245
Re: Progamming help with FSBus dll
Nothing works on the DIO board.
If I put the jumper on J16, the green led lights up so there is power going to the board.
Where is the easiest place to measure the 5vdc on the board?
David
-
01-24-2010, 06:29 AM #246
- Join Date
- Feb 2008
- Location
- Krefeld, Germany
- Posts
- 318
Re: Progamming help with FSBus dll
pin 10 and 11 at the controller.
I would readout and verify the firmware in the Controller via PonyProg.
Stefan
-
01-24-2010, 06:31 AM #247
Re: Progamming help with FSBus dll
Will do and I'll let you know.
David
-
01-24-2010, 07:11 AM #248
Re: Progamming help with FSBus dll
Must be an intermittant fault, it's working now, but not sure for how long.
-
01-24-2010, 07:14 AM #249
- Join Date
- Feb 2008
- Location
- Krefeld, Germany
- Posts
- 318
Re: Progamming help with FSBus dll
Ok, i had some problems with "erased" Controllers some times ago, that happend when i made a shortcut to the powersupply.
-
01-24-2010, 07:19 AM #250
Re: Progamming help with FSBus dll
When it happens again, I'll check the voltage and whether or not I can read the firmware.
I may have shorted it out, but it doesn't seem to have erased the firmware as it's working perfectly at present.
Thanks again Stefan.
David
Similar Threads
-
Fsbus CDK
By flyandre in forum General Builder Questions All Aircraft TypesReplies: 4Last Post: 12-27-2014, 12:58 PM -
Need Help Getting My FSBUS NG I/O Going Again..
By JBRoberts in forum I/O Interfacing Hardware and SoftwareReplies: 14Last Post: 03-21-2010, 01:38 PM -
Fsbus ng io
By Davral in forum I/O Interfacing Hardware and SoftwareReplies: 0Last Post: 01-10-2009, 10:38 PM -
Fsbus 2.4.3
By Anderson/SBSP in forum I/O Interfacing Hardware and SoftwareReplies: 9Last Post: 11-30-2008, 04:25 PM -
Help FSBUS
By cesarfsim in forum I/O Interfacing Hardware and SoftwareReplies: 2Last Post: 10-26-2008, 02:23 PM
Girls in your town
A320 Sound Files Missing