Results 31 to 40 of 45
Thread: My new CNC and AFDS panel
-
12-21-2009, 09:18 AM #31
- Join Date
- Oct 2009
- Location
- Leesburg, Florida
- Posts
- 201
Re: My new CNC and AFDS panel
I agree 100% with autocadplease, I have had conversations with a couple of the home cnc users on this site and they are running cut2d and mach3 as I am. These files are totally interchangeable as they are using the same gcode generator and post processor as I am. DXF file exchange would be better as each user could generate his own gcode file using it. Each file that I upload will contain a short note on what type of material I used, bit size, and approximate cut speeds and spindle speeds.
Milt
-
12-21-2009, 10:28 AM #32
Re: My new CNC and AFDS panel
Hi Guys,
I can supply .DXFs for any type of gears now, I appeared to have got my head around gear cutting ok. I'm now using gears for throttle/potentiometer drives and trim wheel/indicator drives!
Gwyn
737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
http://www.aerosimsolutions.com.au
Supporter of MyCockpit.org, please join me in donating!!!
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikesautocadplease thanked for this post
-
12-21-2009, 07:39 PM #33
- Join Date
- Oct 2009
- Location
- Leesburg, Florida
- Posts
- 201
Re: My new CNC and AFDS panel
Are you using a cnc router or lathe for the gear cutting? I have been trying for some time to cut gears on my cnc router without much luck.
Milt
-
12-21-2009, 11:17 PM #34
Re: My new CNC and AFDS panel
Hey Wendy,
Well, wow what can i say, i remember you telling me what you were planning one cold November morning outside in Lelystad and im speechless with the results you have had so far, looks like i better pull my socks up and get on with things, all this talk of CNC is making me rather jelous cause im still without but that will change soon
You keep up the fantastic work and keep us all posted- - - - - - - - - - - -
Philip Lambert
747-400? nah probably 767 now, FS9, FDT simboards , dunnow about software yet
www.simvionics.co.uk
-
12-22-2009, 01:25 AM #35
Re: My new CNC and AFDS panel
Hey Phil,
Thanks for the kind words. Such a comment from you makes my day.
I still remember our nice chat and hope you will have your CNC very soon. It sure is a lot of fun to work with.
Thanks again, Wendy
-
12-22-2009, 07:38 AM #36
Re: My new CNC and AFDS panel
I'm using "Involute" software to cut gears on the CNC, it's brilliant and really easy to use. I made the trim indicator drive gears for my A340TQ today. The CNC was cutting the gears while I made other parts on the lathe. The A340TQ is almost finished, not much more to do. I'm not looking forward to painting it, I don't like painting but I just bought an airbrush and I'm hoping that helps.
Phil - CNCs are awesome, it's a new hobby!
GwynLast edited by Westozy; 12-22-2009 at 08:07 AM.
737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
http://www.aerosimsolutions.com.au
Supporter of MyCockpit.org, please join me in donating!!!
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikesautocadplease thanked for this post
-
12-22-2009, 04:17 PM #37
Re: My new CNC and AFDS panel
That's going to become a very nice throttle.
Those gears also look very good Gwyn, have to try this out sometime. What tool have you used to mill them ?
Regards, Wendy
-
12-22-2009, 07:46 PM #38
Re: My new CNC and AFDS panel
Hi Wendy,
I used a 1.5mm end mill and the gear cutting software is available here - http://www.realhamradio.com/gearhome.htm It is fantastic and a good buy at AUD$86.00! The software produces .DXFs which I convert in VCarve Pro to GCode. I have cut 2D & Cut3D aswel but I haven't had a play with them yet.
GwynLast edited by Westozy; 12-22-2009 at 07:49 PM.
737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
http://www.aerosimsolutions.com.au
Supporter of MyCockpit.org, please join me in donating!!!
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 DislikesWendy thanked for this post
-
12-27-2009, 09:27 PM #39
- Join Date
- Jan 2007
- Location
- Saskatchewan,Canada
- Posts
- 229
Re: My new CNC and AFDS panel
I just about have the Zenbot CNC set up. Got an old computer with a printer port and WinXP to run it.
I just purchased Mach3 and it has a free version of LazyCam with it.
I am new at Cad software so I was wondering what Cad software would be good for a beginner ??
Also has anyone had any experience with Lazycam ,,would that 2Dcut program be better??
Thanks.
P.S. I think a file sharing area for cad would be a great idea.
-
12-27-2009, 09:37 PM #40
- Join Date
- Oct 2009
- Location
- Leesburg, Florida
- Posts
- 201
Re: My new CNC and AFDS panel
For a beginner, I would recommend Cut2d. It will cost you $150.00 which is cheap for what you will get.... It will take your DXF file and make it into the mach3 gcode file for you. It is very easy to learn and I have used it exclusively to make my panels, even the drawing part. It is not a drawing program per say, but remember, when building panels, we only need circles and squares. When you are ready, I can email you some of the gcode fies that I have made from cut2d for mach3. Send me a pm.
Milt
Similar Threads
-
Engravity AFDS
By Clive in forum I/O Interfacing and HardwareReplies: 7Last Post: 03-15-2011, 05:47 PM -
B737 AFDS panel
By belgianguy in forum I/O Interfacing Hardware and SoftwareReplies: 6Last Post: 01-21-2009, 04:17 PM
Enter and win!
JeeHell FMGS on a remote Computer