Results 1 to 10 of 13
Thread: Static
-
10-14-2008, 05:29 PM #1
Static
I have to bring back some computers in a carpeted room.
Last year in the same room I fried a Hagstrom board with static (that horrible Tic at the end of my finger!!)
Besides removing the carpet or grounding myself is there a way to prevent this ?Jackpilot
B737-700 Posky
FS9/P.Magenta
without PMSystem
-
10-14-2008, 06:31 PM #2
Install a huimidifier in the room. High humidity keeps the static charge down. BUT.... it creates its own set of potential issues.
best,
................john
-
10-14-2008, 07:03 PM #3
Make Your Own Anti-Static Spray
Take an empty spray bottle (such as a window cleaner bottle) and pour in a small amount of fabric conditioner. Fill the bottle with water. The mixture should be about 30:1. Spray the car seats (furniture and/or carpets) and allow to dry. Reapply as necessary.Rodney -
Real 727-200 pit
Last Flown as N392PA
FS9
-
10-15-2008, 05:38 AM #4
- Join Date
- Nov 2005
- Location
- Vancouver BC Canada
- Posts
- 523
OR KEEP YOUR DAMN FINGERS OFF THE HAGSTROM BOARD!!! LOL
Tim
-
10-15-2008, 07:11 AM #5
- Join Date
- May 2008
- Location
- Earth
- Posts
- 288
1. Take off your shoes.
2. Look for a metal item somewhere near and touch it to release the static before touching the the board.
3. Get a wrist strap which is grounded. The strap has a clip so you can just snap it on /off without removing the strap if you move a lot. These straps are not expensive. I learned that one from maintaining a Frasca 142 which has these installed by the factory.Fritz -> Helicopter Cockpit Builder
(FSX | TH2Go | Arduino | Air Manager Avionics | CNC)
-
10-15-2008, 09:08 AM #6
static
Unfortunately even with all the remedies given to you working on carpet is a sure way to generate static, I to had this problem in a carpeted room, even when I was just in the cockpit every now and then I would get shocked.
Other than you taken out the carpet there is no way even with a humidifier will you not stop it, a lot or some you will still get it.
What I did to absolutely stop it was to attach a long wire to a outlet screw , the ones that holds the faceplate on a metal box inside( because it is grounded), or attach it to any thing in the room that is grounded, even the case of a computer that you know is ground.
Then run the wire under your carpet or place it where you cannot see the length of it, and if you fly all the time run it close to your chair or work place and when you begin to work just attach it to yourself, arm or lower leg.
That has worked absolutely well for me.
In the summer time I was fine but when it started getting cooler look out.
Humidifiers work great but they do not cut down all of the static, especially if you decide to make some coffee and you have your socks on and forget that you were charging yourself.
what i did later on was remove the capeting and put in wood flooring
Hope this helps…………..Robert
-
10-15-2008, 09:21 AM #7
- Join Date
- May 2008
- Location
- Earth
- Posts
- 288
-
10-15-2008, 10:15 AM #8
If you can get your hands on a 6"x6" piece of flat copper, mount it to the wall, table, etc and run the ground wire to it. Touch it as you enter the room and most definatley before you touch anything. We used this method in the USAF and it worked well. An open computer case that is plugged in works too. Also, did you know that paper is a great static generator? Don't place your items on it. I learned that one the hard way.
Rodney -
Real 727-200 pit
Last Flown as N392PA
FS9
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
Jackpilot thanked for this post
-
10-15-2008, 10:18 AM #9
Thanks guys...think I will remove the carpet for a wooden floor..another consequence of simbuilding...and use the wrist band in the meantime.
Jackpilot
B737-700 Posky
FS9/P.Magenta
without PMSystem
-
10-16-2008, 04:06 AM #10
If you're set on removing the carpet (and feel it is a sacrifice) you could always look into anti-static carpeting as a solution. Was going to suggest it earlier but I assumed you were looking for a solution in the current setup as opposed to one that involved some alterations and additional spending.
Hi...realize this has been a long time, but I'm heading down the path of building my own 777...
B777 Overhead Panel Design