Results 131 to 140 of 331
Thread: A320 FMGS B50
-
06-02-2018, 07:01 PM #131
- Join Date
- Jan 2011
- Location
- Paris, FRANCE
- Posts
- 53
Re: A320 FMGS B50
Hello Omarhabeeb,
Did you carefully and completely read the Installation Guide ?
You will find pictures in pages 11/12 which tell you about working installations, especially what must be installed on P3D computer... (chapters 3 and 4).
Where are P3D / FSUIPC ?
Where are JeeHell FMGS_Server and FSUIPC modules ?
I don't see them in your described installation…
You also have to check IP addresses etc...
What do you mean about "fmgs is not appearing in the p3d menu" ?
Nothing appears in P3D, you only have to check "Connected to P3D" in FMGS_Server window.
Because it's your first install, I suggest you :
>>> firstly connecting only JeeHell FMGS Server and software modules and make them work,
>>> after this, you will get a first experience and it will be easier for you to connect hardware... (specific hardware modules have to be installed in JeeHell software, as described in chapter 4.1...).
Regards,
Michel
-
06-02-2018, 07:53 PM #132
- Join Date
- Nov 2015
- Location
- Krefeld, GER
- Posts
- 243
Re: A320 FMGS B50
With B50.0 today I experienced several engine start failures after ignition and turning up to app. 27% N2, thereafter automatic Crank and then automatic reignition, which succeded. Wow! Is that a new feature? What leads to the first ignition failure, as it does not appear every time, but in case reproducable for both engines?
Hope, you can help!
Thanks,
Michael
-
06-03-2018, 07:49 AM #133
- Join Date
- Aug 2013
- Location
- eddn
- Posts
- 210
Re: A320 FMGS B50
Hello Guys, Hello Jeehell,
On my last two flights I had a strange issue.
The AP disconnected from time to time (No Ecam Actions). Didn't touch the Sidestick/Ruder or something... also there was normal weather conditions without any windy up and down drifts or thunderstorm.
After the fourth or fifth disconnect (on a 2h flight on IVAO), the MCDU reset (like cold and dark) and all entries are gone. No flightplan, V2, Fuel...
Any Ideas what goes wrong?
Also, I still have the hardware.exe crash on booth clients. No hardware support are installed, only the Joystickclient.
Kind regards
Florian
-
06-03-2018, 01:58 PM #134
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
-
06-04-2018, 01:53 AM #135
- Join Date
- Nov 2015
- Location
- Krefeld, GER
- Posts
- 243
-
06-04-2018, 03:09 AM #136
- Join Date
- Mar 2008
- Location
- France,Nice
- Posts
- 2,652
-
06-04-2018, 08:38 AM #137
- Join Date
- Mar 2017
- Location
- Santiago, Chile
- Posts
- 18
Re: A320 FMGS B50
Jean Luc, it is my understanding that you also can provide an Instructor Operating Station. How can I contact you in order to discuss this?.
Best,
JP
-
06-05-2018, 10:34 PM #138
Re: A320 FMGS B50
AFAIK IOS is only available for the commercial version of FMGS, but it would be fantastic if JL can offer the iOS to private users
Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.
-
06-06-2018, 12:17 AM #139
- Join Date
- Mar 2017
- Location
- Santiago, Chile
- Posts
- 18
-
06-06-2018, 06:08 PM #140
- Join Date
- Aug 2017
- Location
- israel
- Posts
- 36
Re: A320 FMGS B50
Hello Guys
i have some issues with fmgs b50.1/network pc or both
i wrote some notes regarding my problem
i would really appreciate it if you can have a look at them and see if you can help me
i have 2 issues the first concerning the pc network the other concerning fmgs
all pc's are updated the last win10 update
the firewalls are all off according to the IT guy who helped me
windows defender too (but not shure if it's done properly)
first topic network
i have 1 main pc i7 k7700 with 1080ti ( basiclly what a gamer pc has)
and then i have 3 pc's i3 basic stuff 1 i5
the network is built in this way
from the wall to a router via cable and then from the router to a switch also via cable and from there to the pc's also via cables
when i connect them i go to my computer icon on desktop and then to network icon on the left and click on the network
some names of the pc's appear other doesn't ,when i do refresh the page the one they used to be sometimes disappear
and others appear it seems like it's a random thing but definatly i don't see all the pc's of the network (except for the main pc who sees all the pc's)
the other pc's (cpt ,fo ,ovhd central) not always see each other
but when i go to run > cmd.exe> and check the ping on all the pc's then every pc seems to get the signal from the others
how i can make sure that the pc's network is up and running in a stable way?
note on the same router i have also ps4 consoles and xbox console which they are connected via wifi maybe this could disturb the signal and ip adress??
my network details are
when i go to control panel>network and sharing>change adapter settings>right click on the network>properties>internet protocal version tcp/ipv4>properties>
use the following ip address
ip address 10.0.0.30 main pc 10.0.0.50 cpt pc 10.0.0.70 ovhd pc 10.0.0.90 central (pedestal)pc 10.0.0.80 fopc
subnet mask 255.255.255.0
deafult gateway 10.0.0.138
use the following dns server addresses
preffered dns server 10.0.0.138
all pc's are updated the last win10 update
the firewalls are all off according to the IT guy who helpd me
windows defender too (but not sure if it's done properly)
what else is needed??
second topic fmgs
on the main pc i installed p3d latest with fscuipc 5.0, fmgs server b 50.1 ,
and all the hardware from skalarki electronics( fcu,abrk ldg lever ,captain rmp,fo rmp?)
2 logiteck 3dpro joystics,2 saitek rudderpedals,thorottletek which include spoiler and flap levers and few other switches
ip address 10.0.0.30
so in the fmgs installer on main pc i checked the following
main application
master p3d just on this pc
fmgs server just on this pc
ap/fbw just on this pc
sound module just on this pc
intercom module just on this pc
hardware module
fscuipc just on this pc (althought joysticks calibration is done via fmgs so far)
skalarki I/O
Software panels interface
software fcu checked
software fo efis checked
software thr lvr checked
software spoilers checked
software flaps checked
software landing gear checked
when it comes to put the ip address in the installation process on the main pc i check both the boxes which says
this pc runs p3d checked
this pc runs fmgs server checked
so ip box is automatically greyd when the above are checked so ip not needed
and then joystick calibration
i did the calibration via fmgs and then save
but regarding to the calibration few question
1 if i do calibration via fmgs do i need to check the box fscuipc support?
2is the calibration via fmgs a must ?or i can do it via fscuipc?
3 i red on the forums that fmgs server works only if i do joystick
calibration and saving cause after the saving fmgs installator
generate a file that without it the hole software will not work
is that correct?
now when i run the same installer
on the captain pc i choose these option
from main application
pfd captain side checked
nd captain side checked
nothing else checked in the installer fill the ip of the main pc (p3d ,fmgs server) which is 10.0.0.30
on the fo pc the installer
main application
pfd fo side checked
nd fo side checked
nothing else checked in the installer fill the ip of the main pc (p3d ,fmgs server) again is 10.0.0.30
on overhead pc (with 2 touch screen monitors)
in the installer i choose
software panel interface
overhead interface checked
nothing else checked in the installer fill the ip of the main pc (p3d ,fmgs server) again 10.0.0.30
on the central pc 2 monitors
1 normal
1 touchscreen
main application
ewd checked
sd checked
mcdu captain checked
mcdu fo checked
ddrmi checked
clock checked
software panel interface
software ecp checked
software cpt acp checked
software fo acp checked
software cpt rmp not checked cause i have hardware
software fo rmp not checked cause i have hardware
nothing else checked in the installer fill the ip of the main pc (p3d ,fmgs server) again 10.0.0.30
after all the installations i restart all the pc's
run the the a320 fmgs cold and dark icon on main pc then run the other's
as administrator
the results are
the only thing is that i see connected is
ap/fbw connected but sometimes signal keeps flipping althought it's on the same pc of the server(i mean it keep changing connected/not connected)
fcu connected in green
mcdu connected in green
fo mcdu connected in green
all the other modules seem to be disconnected
now regarding ap/fbw (in addition to the server )as far as i red in the
fmgs guide without this module nothing works
and i have to choose 1of 2 aircrafts cfm/iae
in this module we have 2 aircraft type coefficents
cfm/iae
what i have to do in the reload coefficent and show editor
is there something that i have to do ?
so we have p3d with fscuipc skalarki profile 5 and fmgs server
i have to start all of them but the question is in which order ?
does it make a difference?
so this is what i get from the software
or that there is a problem in the network and this is why i get these results
bare in mind that for 1 hour i had everything connected and running ( i don't remember what i pressed to make it work) i don't know what happened after restart the pc maybe
any help would be appreciated
a step by step process would be perfect
Regards
Omar
Beautiful Womans in your town for night
B_34 TOGA takeoff