Page 11 of 31 FirstFirst ... 78910111213141521 ... LastLast
Results 101 to 110 of 309

Thread: A320 FMGS B45

  1. #101
    25+ Posting Member
    Join Date
    Dec 2013
    Location
    Vienna/Vienne
    Posts
    36
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by Leonidas View Post
    Hi
    Under what circumstances NAV ACCURANCY DOWNGRADED and UPGRADING again?
    Hyi guys!

    Please donīt mix up procedures and systems:
    The A320 FMS calculates a position tolerance.
    Navigation accuracy HIGH means, the calculated position tolerance is within the required navigation performance (RNP), LOW if the tolerance is greater than RNP.

    If the system switches from HIGH to LOW, you get:
    NAV ACCUR DOWNGRADE (and vice versa with UPGRADE)

    What you do with that message tells you your procedure. You wonīt fly a go-around if you do an ILS approach (because you follow the ILS signal), maybe you have to fly one on RNAV/RNP appraoches (where you rely on GPS).


    By the way: B45 is great. This is unbelievable perfectly done. Thank you JL!!

    Kind regards
    Michael

  2. Thanks SSO thanked for this post
    Likes Leonidas liked this post
  3. #102
    25+ Posting Member mikatsan's Avatar
    Join Date
    Oct 2015
    Location
    Greece
    Posts
    32
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by jeehell View Post
    The issue with ILS and RWYs is due to mis alignment between the navdata from Aerosoft/navigraph and the facilities inside FS/P3D.
    To counter that, when compiling the navdata bin files, my soft reads directly the FS/P3D BGL files to correct the navdata with ILS/RWY lat,lon,course.
    With P3D V3, now everythign has to be put outside P3D folder, this could be the issue, particularly if your problem is only with addon sceneries.
    The problem is also present with Runways which changed QFU, or which were later added, so the original runway naming changed to for example R/L or C.

    JL

    Hello, any help with that?

  4. #103
    25+ Posting Member
    Join Date
    Dec 2013
    Location
    Vienna/Vienne
    Posts
    36
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by OmniAtlas View Post
    Does anyone know when the

    'COM VHF1 EMITTING' on the SD is triggered?

    Should it always display with PTT? Or only if PTT has been held down for several seconds?

    Thanks.

    If VHF emitting more than 60s.
    Greets
    Michael

  5. #104
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,107
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by filippoporcari View Post
    i don't have my fcom in my hands now: what i'm sure it DOES NOT happen every time ptt is pressed for normal operations. if i remember correctly it appears if u have a stuck mike/ptt button.(ie button pressed for long time)
    regards
    fil
    Cheers, thanks -- the PTT event is now programmed as a PUSH and RELEASE trigger. I do not get the VHF1 emitting message now.

    Now to figure out how to link it to an ACP/RNP.

    JL -- you mentioned your software will be compatible with FDS ACP?

    Regards.
    Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.


  6. #105
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,107
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by Migelito View Post
    If VHF emitting more than 60s.
    Greets
    Michael
    Noted, you must be a real world pilot.
    Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.


  7. #106
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,652
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by OmniAtlas View Post
    JL -- you mentioned your software will be compatible with FDS ACP?
    As far as I know, FDS does not make plug'n'play ACP panels. If you can assign each buttons directly in IITCreator (using an FDS IO board) then yes.

    Regards,
    JL

  8. #107
    2000+ Poster - Never Leaves the Sim


    OmniAtlas's Avatar
    Join Date
    Jun 2012
    Location
    Sydney, Australia
    Posts
    2,107
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by jeehell View Post
    As far as I know, FDS does not make plug'n'play ACP panels. If you can assign each buttons directly in IITCreator (using an FDS IO board) then yes.

    Regards,
    JL
    Thank you JL -- I will correspond with FDS and see what they can offer. Otherwise it looks like Skalarki is the only vendor that offers a PnP version?

    On a side note -- a small request JL -- would it be possible to implement a PFD/ND / etc. display screen ratio lock? I would like to maintain the original ratio of the window when resizing (resize in the corner only with double arrows) but have difficulties maintaining the correct X and Y measurements as intended. It would be fantastic if this feature could be implemented. Thank you!

    Ben
    Soarbywire - Airbus Flight Simulation and Engineering | Jeehell FMGS - Free professional A320 avionics software for the cockpit enthusiast.


  9. #108
    300+ Forum Addict
    Join Date
    Sep 2010
    Location
    LGTS
    Posts
    424
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by OmniAtlas View Post
    Thank you JL -- I will correspond with FDS and see what they can offer. Otherwise it looks like Skalarki is the only vendor that offers a PnP version
    Ben
    And CPFlight ...

  10. #109
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,652
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Quote Originally Posted by OmniAtlas View Post
    On a side note -- a small request JL -- would it be possible to implement a PFD/ND / etc. display screen ratio lock? I would like to maintain the original ratio of the window when resizing (resize in the corner only with double arrows) but have difficulties maintaining the correct X and Y measurements as intended. It would be fantastic if this feature could be implemented. Thank you!
    Ben, you can manually change the size (width and height) of any EIS app by going in the folder c:\A320FMGS\EIS and there you look for the files such as PFD.ini, FOPFD.ini etc... Inside those files, you can set the top left corner position (TOP and LEFT entries) and width height as well. This is in pixel (x=0 y=0 is the top left corner of your screen).

    JL

  11. #110
    150+ Forum Groupie


    Miatanet's Avatar
    Join Date
    Dec 2011
    Location
    Switzerland
    Posts
    206
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B45

    Hi all

    since the new version in correlation with IOProfiler 5.0 I got this message:



    I thought I have seen one post to that similar error message but can't find it anymore. It says "index is out of the array section", when pressing Bat1 or Bat2 on my OverHeadPannel (Skalarki). Does someone has a clue what that could be? Is the first time that I get this error...

    Best regards
    Stefan

    EDIT:
    Problem solved. Again a quick and high quality support by Marcin (Skalarki). Had a wrong setting in the xml file....

    Best regards
    Stefan
    Attached Images Attached Images

Page 11 of 31 FirstFirst ... 78910111213141521 ... LastLast