A320 FMGS B38

[tcane]

Oh Oh Oh OH Guys....

Big Big fu...... misstake from me. This is so embarrassing that i have told you so annoyed all the time. Really stupid from me!!!

I find out my problem....
Long time ago i changed the default ports because got some other issues....
In the last hour i made an complete fresh and clean installation of Jeeheel and saw that the default Ports are usually other!
Changed all to default... all works without any crash and clients displayed as connected.

I`ll thump me with the hammer to the head! BIG BIG SORRY FOR THIS GUYS!!!

But i find a small issue with the SIOC Creator...
It doesn´t saves the "Use SWTCHG/RUDDER TRIM" when i enabled it.

AGAIN: A BIG SORRY FOR THIS AND THX FOR YOUR PATIENCE!

Cheers
Florian

[emani]

Hello everybody,

I'v got a problem with the MCDU modul. When I press the PROG or PERF key the following error message is displayed

MCDU DIPLAY PROBLEM PLEASE REPORT ISSUE


All other keys (and modules) work fine.



Version B38.3 is installed but I face the same issue with older versions. The MCDU is running on a touch screen monitor (10 inch) but with a normal TFT I get the same error message. And there is no difference using the mouse or my fingers to press the button.
As I'm still testing A320FMGS is running on a single PC.

Regards

Mario

[AirbusMike]

Hello everybody,

I'v got a problem with the MCDU modul. When I press the PROG or PERF key the following error message is displayed

MCDU DIPLAY PROBLEM PLEASE REPORT ISSUE


All other keys (and modules) work fine.



Version B38.3 is installed but I face the same issue with older versions. The MCDU is running on a touch screen monitor (10 inch) but with a normal TFT I get the same error message. And there is no difference using the mouse or my fingers to press the button.
As I'm still testing A320FMGS is running on a single PC.

Regards

Mario

Hi Mario,

I had the same with 38.3 but with 38.4 the problem is gone

BR Mike

[AirbusMike]

Hi Folks,

I've a small question concerning the FSUIPC pipe &H78EE (OVHD input) as soon as I write a command the input
from the graphical OVHD does stop working but the lights are working.. Is there an option to have both inputs?
(I'll try to wirte my own driver for my cockpit hardware and sometimes it's good to have both running for testing )

BR Mike

[jeehell]

@AirbusMike: I see no reasons for the OVHD UI to stop working, can you elaborate a bit more?

regards,
JL

[AirbusMike]

@AirbusMike: I see no reasons for the OVHD UI to stop working, can you elaborate a bit more?

regards,
JL

Hi JL

I had the OVHD UI running and did turn on the couple of things with the mouse (like EXT PWR etc..) and it worked find
The UI was stil running and I did send one byte to 78EE (value 47 for Pack 1) and the PACK1 light on the UI turned on and
off as expected but after this all mouse inputs on the UI didn't work anymore..
I did close and restart the UI but no change... but the FSUIPC input did still work and the light on UI did respond
That looks to me that the FSUIPC inputs were processed.

There is one more question from my side is it possible to have not only toggle commands for the Korry switches
a few in the ovhd are also alternating switches (solid ON or OFF position like fuel pumps flt controls packs etc)

like
78EE value 47 (Pack 1 TOGGLE)
78EE value XXX (Pack 1 ON)
78EE value YYY (Pack 1 OFF)

That would be really nice

best regards
Mike

[Miatanet]

Hi all
since the last update my system crashes without an error message. all systems are no longer usable after take off. using all Skalarki HW. Is there a error log file which tells me why all systems (FCU, MCDU, RMP etc.) are not responding anymore?

Regards
Stefan

[jeehell]

@Mario and Stefan: did you upgrade to 38.4 by first using the full installer ( http://www.jeehell.org/A320FMGS_B38.4.exe ) then doing the auto updates?

@Airbus Mike: I tried the FSUIPC module alongside the OVHD UI and I do not have any issues. It is not possible to add the full ON/OFF logic for all korries in FSUIPC module. You'll have to do some sort of synchronization yourself (it's not too hard to do since the OVHD panel always starts in the same SW state).


JL

[Miatanet]

Hi JL,

yes I did, and before all systems are inop I see the message on the MCDU Display problem... like emani wrotes. That is real strange because all went fine so far.... all freezes and no knob is functioning. No error message, so I can't tell what is the problem. I may need to install again a fresh installation on all systems. Will check during thze weekend and report out come.

BR
Stefan

[Miatanet]

Strange, did a clean install but Navigation does not create .bin files. Do I need to start a special exe?
regards
stefan