Results 1 to 4 of 4
  1. 11-05-2009, 09:48 PM #1
    sja
    sja is offline
    10+ Posting Member
    Join Date
    Dec 2007
    Location
    Scotland
    Posts
    12
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Correct flaps annunciation in EICAS page

    Anyone know how to get the flap indicator to show UP,1,2,5,15 etc like it should on the 737NG?

    I'm fed up copying the settings to the pfd.ini file and saving it then restarting the GC just to see it work for a few minutes then go back to UP,40,40,40,15!

    Those latter settings were in the pfd.ini file (don't know where they came from) but they seem to be getting copied back from somewhere once the EICAS mode of the GC fully initialises.
    Reply With Quote Reply With Quote
  2. 11-06-2009, 02:13 PM #2
    gandofalcon
    gandofalcon is offline
    10+ Posting Member gandofalcon's Avatar
    Join Date
    Feb 2008
    Location
    Spain
    Posts
    11
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Correct flaps annunciation in EICAS page

    Hi what type has you in the CDU?
    Reply With Quote Reply With Quote
  3. 11-07-2009, 04:18 AM #3
    sja
    sja is offline
    10+ Posting Member
    Join Date
    Dec 2007
    Location
    Scotland
    Posts
    12
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by gandofalcon View Post
    Hi what type has you in the CDU?


    Posted via Mobile Device
    Reply With Quote Reply With Quote
  4. 11-07-2009, 04:35 AM #4
    sja
    sja is offline
    10+ Posting Member
    Join Date
    Dec 2007
    Location
    Scotland
    Posts
    12
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I have 737-700.
    Yesterday following the advice on PM website to push key LSK1 during perf init I had the flaps indicator as I wanted it.

    I had previously left the CDU alone as the aircraft type was correct.

    So it appears solved!
    Posted via Mobile Device
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. CDU 406-Cannot enter Flaps setting on T/O page
    By PeterH in forum PM Boeing FMC/CDU
    Replies: 8
    Last Post: 09-30-2010, 03:23 AM
  2. F6 page GC Boeing - Flaps and autobrakes
    By timonier in forum PM Boeing GC
    Replies: 4
    Last Post: 08-03-2010, 04:08 PM
  3. Airbus Flaps in Upper EICAS
    By luisgordo in forum PM Airbus GC
    Replies: 8
    Last Post: 06-28-2008, 02:07 PM
  4. Airbus Flaps in Upper EICAS
    By luisgordo in forum PM General Q & A
    Replies: 7
    Last Post: 03-01-2008, 03:56 PM
  5. PM eicas display with aerosoft eicas hardware
    By npbosch in forum PM Boeing GC
    Replies: 7
    Last Post: 10-03-2007, 08:37 AM