Printable View
Hello,
I prepare has connection of my OVH 747 and I meet some difficultees to
identify certain
variables.
somebody could it indicate the variables of the following functions to me if
it exist.
747:
- Electric eng control 1,2,3 and 4
-Elec Standby Power - AUTO
-Elec Standby Power - BAT
-IRS L : ALIGN
-IRS L : NAV
-IRS L : ATT
-IRS C : ALIGN
-IRS C : NAV
-IRS C : ATT
-IRS R : ALIGN
-IRS R : NAV
-IRS R : ATT
Thank you in advance
cordialy
jean luc
Just enable the display of the variable names... and it will
say which ones they are. (in development mode)
> - Electric eng control 1,2,3 and 4
Not implemented yet.
> -Elec Standby Power - AUTO
> -Elec Standby Power - BAT
StandbyPower ... values 1 and 2...
> -IRS L : ALIGN
> -IRS L : NAV
> -IRS L : ATT
IRSSelector1 to 3...
Ciao
Enrico
Hello Enrico,
Thank you for this informations.
I use IO-CARD interfaces , what the number of FSUIPC variables for
programation
Io-CARD software ?
cordialy
jean luc
Hello enrico,
excuse me , but I had not understand well your answer
,now it's OK and i understand for the variables .
thank you
cordialy
jean luc
> excuse me , but I had not understand well your answer
> ,now it's OK and i understand for the variables .
You mean you are OK with the offsets now? I think you mean
those when you say IOCard numbers, right?
Hello enrico ,
I return towards you relating to functions IRS.
I understands well for IRSSelector1 to 3...
On the other hand a the sysvar file I do not find IRSSelector?
Just
56C1 1 IR1Sel //Airbus
56C2 1 IR2Sel
56C3 1 IR3Sel
it' correct for Boeing ?
56C1 1 IR1Sel -ALIGN
56C1 2 IR1Sel -NAV
56C1 3 IR1Sel -ATT
Thank you in advance , tout ceci est encore assez nouveau pour moi !
cordialy
jean luc
You probably do not have the current version of pmSystems,
you should have the following in your sysvar.txt file:
5710 1 IRSSelector1
5711 1 IRSSelector2
5712 1 IRSSelector3
5714 1 IRSStatus //this can be used to set the various
conditions
5715 .0 IRSNotAligned //will disable GC
5716 2 IRSAligned1 .1
5718 2 IRSAligned2 .1
571A 2 IRSAligned3 .1
"BOINET jean luc" wrote in message
news:385377.77259@wb.onvix.com...
> Hello enrico ,
>
> I return towards you relating to functions IRS.
> I understands well for IRSSelector1 to 3...
> On the other hand a the sysvar file I do not find
> IRSSelector?
> Just
> 56C1 1 IR1Sel //Airbus
> 56C2 1 IR2Sel
> 56C3 1 IR3Sel
>
> it' correct for Boeing ?
>
> 56C1 1 IR1Sel -ALIGN
> 56C1 2 IR1Sel -NAV
> 56C1 3 IR1Sel -ATT
>
> Thank you in advance , tout ceci est encore assez nouveau
> pour moi !
>
> cordialy
>
> jean luc
>
Hello enrico,
Thank you,i also will update my software .
cordialy
jean luc
Hi Enrico,
I did see the correct variables names in PMSystem. Thanks.
But is the system working already? (Parcially blanking displays
(PFD/ND) as long the IRS isn't aligned)
As yesterday with builds GC453e CDU377d situation was behaving as before
(when entering coordinates in the cdu - screens were coming immidiately
to live - nevetheless IRS knobs were off or NAV.
I saw counting as small figure in pmsystem (next to irs panel) but these
didn't seems to have an influence.
Is there a setting which has to be changed in the ini's or isn't it
implemented yet for the Queen?
B. rgds
Michel
Hi,
it is implemented *only* for the 747 and I would have to
check the conditions when it wouldn't apply.
On the ground, not moving, it works as it should.
Enrico
"Michel Vandaele" wrote in message
news:385582.77259@wb.onvix.com...
> Hi Enrico,
> I did see the correct variables names in PMSystem. Thanks.
>
> But is the system working already? (Parcially blanking
> displays
> (PFD/ND) as long the IRS isn't aligned)
>
> As yesterday with builds GC453e CDU377d situation was
> behaving as before
> (when entering coordinates in the cdu - screens were
> coming immidiately
> to live - nevetheless IRS knobs were off or NAV.
>
> I saw counting as small figure in pmsystem (next to irs
> panel) but these
> didn't seems to have an influence.
>
> Is there a setting which has to be changed in the ini's or
> isn't it
> implemented yet for the Queen?
>
> B. rgds
> Michel
>
I looked at this portion a bit, if I am in the air switch
the IRS off, I can't get them to display anymore. There must
be a way around this. (because if the (fsGS > 0) part.
I see no reason why the displays are not switched off in you
setup though. Are you certain your sysvar.txt has been
updated with the version currently online?
Ciao
Enrico
"Enrico Schiratti" wrote in message
news:385646.77259@wb.onvix.com...
> Hi,
>
> it is implemented *only* for the 747 and I would have to
> check the conditions when it wouldn't apply.
>
> On the ground, not moving, it works as it should.
>
> Enrico
>
> "Michel Vandaele" wrote in message
> news:385582.77259@wb.onvix.com...
>> Hi Enrico,
>> I did see the correct variables names in PMSystem.
>> Thanks.
>>
>> But is the system working already? (Parcially blanking
>> displays
>> (PFD/ND) as long the IRS isn't aligned)
>>
>> As yesterday with builds GC453e CDU377d situation was
>> behaving as before
>> (when entering coordinates in the cdu - screens were
>> coming immidiately
>> to live - nevetheless IRS knobs were off or NAV.
>>
>> I saw counting as small figure in pmsystem (next to irs
>> panel) but these
>> didn't seems to have an influence.
>>
>> Is there a setting which has to be changed in the ini's
>> or
>> isn't it
>> implemented yet for the Queen?
>>
>> B. rgds
>> Michel
>>
>
Hi Enrico,
Thank youi for looking at it.
I'm two days away, so will check it on thursday.
"Enrico Schiratti" wrote in message
news:385860.77259@wb.onvix.com...
>I looked at this portion a bit, if I am in the air switch
> the IRS off, I can't get them to display anymore. There must
> be a way around this. (because if the (fsGS > 0) part.
>
Hmm from memory I think if for what ever reason the IRS are switched of,
there is now way they can't be fully aligned again. Via ATT a present hdg
can be put in , but that's all I think. But as I said, its form my memory.
Will have to check
> I see no reason why the displays are not switched off in you
> setup though. Are you certain your sysvar.txt has been
> updated with the version currently online?
>
I tought I did, but will check it before I test again
Many thanks for help
Michel
> Ciao
>
> Enrico
>
> "Enrico Schiratti" wrote in message
> news:385646.77259@wb.onvix.com...
>> Hi,
>>
>> it is implemented *only* for the 747 and I would have to
>> check the conditions when it wouldn't apply.
>>
>> On the ground, not moving, it works as it should.
>>
>> Enrico
>>
>> "Michel Vandaele" wrote in message
>> news:385582.77259@wb.onvix.com...
>>> Hi Enrico,
>>> I did see the correct variables names in PMSystem.
>>> Thanks.
>>>
>>> But is the system working already? (Parcially blanking
>>> displays
>>> (PFD/ND) as long the IRS isn't aligned)
>>>
>>> As yesterday with builds GC453e CDU377d situation was
>>> behaving as before
>>> (when entering coordinates in the cdu - screens were
>>> coming immidiately
>>> to live - nevetheless IRS knobs were off or NAV.
>>>
>>> I saw counting as small figure in pmsystem (next to irs
>>> panel) but these
>>> didn't seems to have an influence.
>>>
>>> Is there a setting which has to be changed in the ini's
>>> or
>>> isn't it
>>> implemented yet for the Queen?
>>>
>>> B. rgds
>>> Michel
>>>
>>
>