Printable View
So in the the CDK i can do a echo test with no problem and no errors. I was able to flash the Controller and it works i can Turn on and off the LEDs on the DO64 but for some reason its stuck on CID 31 default. I cant seem to be able to write the controller to any other CID. I can change the CID in the CDK but to write say CID 7 to the Controller it does it i click the button 3 times like normal ans it says 1, 2, OK but to go test the controller its still stuck on CID 31. Any ideas?
Do you set the Jumper how it is writen in the manual?
There is the 6 pin ISP and the 3 pin int ext power and a 10 pin and thats it there isnt any other jumpers for the DO64
Read the manual of the DOUT board.
Quote:
Setup CID
Any FSBUS controller have a CID to identify it in the network.
The value from 1 to 30 can be burned into the ATTINY EEPROM with the Fsbus CDK.
(select [Setup] – [FSBUS setup]).
Usually this is done once in the controllers lifetime. To prevent accidently unwanted changes
of the CID, you need to set a jumper from pin 4 to 6 on the ISP connector J2.
This jumper enables the setup of the controller. After setup you must remove this jumper
again.
nope that didnt work for the DO64 its still stuck on ID 31
strange, that is from the DO64 Board manual and work on my 4 boardīs.
k so 1 i have the power connected to int 2 i have the 10 pin pluged in 3 then the green light flashes 31 times to show that its CID31 4 i set the jumper from 4-6 5 i go in CDK and click three times to set the CID to 1 6 i take the 4-6 jumper off 7 try testing the DO64 and its still on CID31
update so..... I was able to get my 6 pack to be any CIDs i wanted them to be and they work but..... i cant get my DO64 to change from CID31 so i tried moving the Controller from the DO64 and put it into the 6pack and try to give it a CID that way and then put it back and that didnt work grrr Well maybe i can just leave it at 31 since it is working at 31 hehehe
Update... So i Started over and redid the COM PCB and that was my problem! Now im able to do any thing i want to do with NO errors!
Realy good, have fun with your Do64 Board.
Well thats the thing.... Im now able to get allllllllllll of the Boards working now DO64, IO, 6Pack all of them
Hello,
I have a strange behavior on my 6 pack Fsbus display card. After CID set, it randomly reset to 31, after 1 or more DC disconnects. How to fix it? All the jumpers are always sets, cause without jumpers displays doesn't power on. Is this normal?
Thanks
Francesco
Hello,
please describe what you do step by step.
Also make a picture of the board with the Jumpers for setup the CID and normal usage.
Stefan
Hello,
first I set the first jumper to flash the first CID. After it's set I test with it with Fsadmin and it works fine with correct CID. After that, I remove the jumper from the first place and set it to the second place to set a new CID for the second display, and so on...After that i set all jumpers (as you can see from the picture, the four jumpers are soldered), and it works fine, but after 1 or more DC power disconnect the CID reset to 31.
Attachment 7527
Ok, the way ist ok.
How much voltage and current have your power supply?
Hello, voltage is 5 V, current I don't know, but i have an IO board and it works very well. It's very very strange!
I know that Problem, in the most times it is a to low power supply.
In the moment when you start all the Power supply dosnīt supply 5 Volts because to may "users".
When the Voltage is lower than 3.6-3.9 Volts it is possible that the EEPROM Part of the Atmel delet all.
Get the Atmel Datasheet and setup the "BOD" or use a more stable power supply.
I use 5V 20A.
ok,
i'll try a more powerfull power supply. Currently i'm using 5v from usb port!