Hi JL,
two more test flight behind. Minor lagging but nothing too bad.
Here is a picture of strange values on N1 display:
Attachment 6646
Regards,
Tommi
Printable View
Hi JL,
two more test flight behind. Minor lagging but nothing too bad.
Here is a picture of strange values on N1 display:
Attachment 6646
Regards,
Tommi
Hi
For those having difficulties with FDS modules, please try this DLL (overwrite the one in hardware modules folder):
http://www.jeehell.org/JeeHell_IIT.dll
Marcus, you say you have 2 analog axis from SIOC Creator, did you declare them or they "appeared" without you wanting them? Also, I tested IITcreator on an XP sp3 32 bits without troubles. Maybe you miss the file interfaceIT.dll?
Cheers,
JL
I have is exactly the same error,Quote:
Originally Posted by Marcus
@Jeehell,
what did you mean with "declaire" a Axis? I have used the Nisc-Tab in SIOC-Creator. Klick "Axis1", use Input, Device, Left, center, right and "Apply Configuration". Now i have this in the SIOC-Script.
With regards
Helmut
The two analog axis (flaps & slats) I declared myself in previous versions, also tried to re-configure all axis in FMGS creator, but didnt help.
I cant remember if the interfaceIT.dll were missing, if I try to rename it and start it says that specific .dll is missing. Due to the FCU going blank I temporairly switched back to B24.1 and also recieved the same error on the two clients when trying to open ITTcreator. Also tried to install .NET 4 on the clients, since only the server had it installed, but didnt help.
Next time I'll be at the sim is on Sunday, will have a lock then probably. Will try that JeeHell_ITT.dll as well.
Thanks :D
Marcus
Attachment 6648Hello,
here some feedback for the new fsuipcmodule.dll...
To be honest, I am still a bit confused: I exchanged the dll's in hardware modules folder... The TRK/HDG mode issue was gone. After a short period I somehow managed to get the old behaviour --> TRK/HDG mode was again inverse on soft and hardware. So I loaded the old dll again and then the new one again... since then I didnt have any problems with HDG/TRK. So I hope it's solved :)
For Barometric pressure: It seems to work but if I switch units from 1013 to 29.92 HG I cant change the value with the decoder. The 29.92 are displayed but as I turn the decoder in any direction rubbish apprears on soft and hardware.. but only when in HG. It works in hPa units. And the QFE/QNH LED outputs are not working... but I have not even tried them with B24.1
Rest of FCU works as it should. Execept the EXPED function has a strange behaviour. I cant turn it off (not in soft nor hardware) and it locks strange on FMA. EXPED and i.e. VS +500 are overlapping an shown at the same time. So I guess the "EXPED" word does not disapprear on FMA. However, new Vertical Modes are just put above the "EXPED" wording. See attached pic.
Now to the good things which should be mentioned as well: I really like the new flight model. It seems to be smoother in pitch and roll. What have you changed??? I also noticed you changed the schematic spoilers on SD, you added reasonable max/min values on the FCU. The APs remain ON after Autoland and the AC does some automatic steering (it does not keep on centerline though) ... all VERY NICE!!!
I am looking forward to try the new network apps.
Thank you!!
Rob
Hello again,
I have to correct myself: Just turn on the software and hardware FCU... AGAIN... HDG/TRK mode is always inverse.
In addition I tried to use the network... I can't get it to run.
The WideFMGS keeps connecting/disconnecting on both ports 8003/8004 on the client pc. The display stay blacks :(
Strange... I used port 8003 successfully with B24.1 in this setup.
Regards,
Rob
Hi,
OK I found the issue with the SIOC axis. I will make the correction tomorrow if I find the time to upload etc...
Rob, I will try to check with Skalarki what might be the problem. As for the networking issue, it can be caused by firewall settings or bad configuration (like wrong IP address by mistake). Most people seem to be able to use it without issues??
Can you try to shut down the sound module and the hardware module? it might be another cause.
Cheers,
JL
Hello JL,Quote:
Originally Posted by jeehell
sounds good.
WR
Helmut
Hi JL,
after hours of searching I ve to admit that I was too stupid. I checked the Firewall several time. For some reason I have not seen that the Server has been set blocked. Now it works on the network. I am really sorry!
Anyhow, do you know the reason why it keeps connecting so often which then leads to an update of the FMA and the white boxes i.e. on PFD... even I have not touched anything? Is it CPU related? My current client is VERY old :)
Thanks for contacting Marcin wrt FCU issues :)
Rob
Hi,
even if it disconnects then reconnects every now and then, it should'nt update the FMA, I will try to look at that. Do you have fluidity issues on the network clients?
JL