A320 FMGS beta 26

hi jeehell.

Yes I did it in the FMGS, I set the detents values there but FSX didnt accelerate the engines.

Also i disabled the Fly by wire in the AP.FBW module , can that be the cause of the problem?

Regards, and thanks!

Adonis

Hi,

Stupid questions, but it already happened: are the engines running?
Also, in AP/FBW module, did you select an aircraft in the dropdown list?

Why did you disable the FBW?

JL

Hi JeeHell,

I have the same problem of adonis martinez but with FS9. I configure correctly the detents in FMGS.
And I have another big problem: with the rotation of V/S encoder the displays and leds of my cockpit (SIOC system) to light up in random mode.. It happened also with the V/S rotary on the screen.

Bye

Umberto VR

Hi,

I forget the last thing: with the last version of FMGS 19.2 on my cockpit the Voltmeter displays of battery don't work (SIOC system). Before with FMGS version 18 they worked correctly.
I use FS9, FSUIPC 3.99, SIOC 3.5

Thank you for great work and support..

Bye

Umberto VR

Hi Jeehell.

there is no more stupid question that the one that is never done ;)

Yes both engines are running and I selected the plane from the list as usual in the FBW.

I disabled the fly by wire because for some reason when it is checked my airplane is uncontrolable, so the raw joystick input solves the problem also the autopilot engaged is not able to control the plane.

Do you know if there is any known problem if FSx service packs are installed?


thanks
Adonis

Hi,


The throttles not spooling the engines is a first. Adonis, what version of FSUIPC do you use? I had troubles with the last one, and I stick to V4.6 for the time, maybe that is a clue for you.
Also, what aircraft are you two using? iFDG or PA, or another one?
What's weird is that you said the EW/D correctly moves the white circle on the N1 display!? This means to me that either the AP/FBW module is not working or there is a problem with FS...

As for FSX, I use a version with both SPs installed, so it is not a problem.


Concerning SIOC and Voltmeters displays, I recently rewrote completely the SIOC handling, and I think I forgot to add that feature. I'll look at that for next version.

JL

Hi JL,

I use the A320 for FS9 IFDG inserted into the folder of the latest version 19.2 of FMGS. My throttle levers are two separate entities with two potentiometers connected via the analog inputs of the expansion card opencockpits and calibrated with your FMGSconfig.exe
For the problem of Vertical Speed ​​encoder that turns on randomly all displays and outputs of my cockpit have discovered what may be? With version B18 did not happen.

Thank you very much for your patience

Umberto VR

Umberto,
Did the SIOC axis work in versions earlier than B19? on the E/WD, are the white circle moving correctly on the N1 gauge when you move the THR LVRs?
For the VS encoders, I will try to check a cuople things, but it's weird. Did you re-apply configuration when upgrading to B19.2?

Adonis, what version of FSUIPC do you use? I noticed I had troubles with v4.7, so I stick to v4.6 for the time.

JL

Hi JL,
yes the SIOC axis work correctly in version B18 but I don't remember if on the E/WD, the white circle moving correctly on the N1 gauge when I move the THR LVRs. In these days I'll try again...

I might have found the problem of Vertical Speed​​. Its value is sent only to the fourth displays and not to others. So I think that the system goes crazy.
The value of the other three displays is always 0.
The fifth display, the minus sign, is working properly
This is a small text of IOCP console:
8=50 - FCU_VS_DISP4
8=40 - FCU_VS_DISP4
8=30 - FCU_VS_DISP4
8=20 - FCU_VS_DISP4
8=0 - FCU_VS_DISP4
8=-10 - FCU_VS_DISP4
9=-999998 - FCU_VS_DISP5
8=-20 - FCU_VS_DISP4
8=-30 - FCU_VS_DISP4
8=-40 - FCU_VS_DISP4
8=-60 - FCU_VS_DISP4
8=-70 - FCU_VS_DISP4
8=-80 - FCU_VS_DISP4
8=-70 - FCU_VS_DISP4
8=-80 - FCU_VS_DISP4
8=-100 - FCU_VS_DISP4

I hope this help you...
Umberto VR

thx Umberto, I will look at that more precisely.
Keep me posted for the THR LVRs.

JL