A320 FMGS B35

Quote:

---

Originally Posted by SSO

Stefan,

As you can see in my other post on the subject it is VERY tricky.
What I have ended up doing is:
Set Idle to 1900 +/- 2000.
Set reverse idle to -2000 +/-1900.
When setting reverse idle, the counter will run 0, 1000, 2000, 3000 etc to 65000. You need to press the APPLY button when it passes the 2000. I think I had to try 20 times per throttle to get my timing exactly right.
That is why I requested that the values could be manually overrided rather than only reading the pot input.

Have fun ;-)

---

Hi Stephen
the problem is that it does not counter as before. When chosing rev. Position and moving the lever it does not change the value. I do not remember if idle value was zero before.

Best
stefan

Quote:

---

Originally Posted by miatanet72@gmx.ch

Hi Stephen
the problem is that it does not counter as before. When chosing rev. Position and moving the lever it does not change the value. I do not remember if idle value was zero before.

Best
stefan

---

Did you reassign your switch buttons?
You should see the slider move between -65000 to zero to 65500 at the bottom of the complex joy assignment window.
That part works fine for me.

Quote:

---

Originally Posted by SSO

Did you reassign your switch buttons?
You should see the slider move between -65000 to zero to 65500 at the bottom of the complex joy assignment window.
That part works fine for me.

---

Reassigned the switches but as I said, my Idle position is 65500 not ZERO, my TOGO is Zero, when in complex window it just counts from 65500 to 0, when pressing the switch its jumping from middle position to the left end on reverse trust on the resulting axis bar, so here it seems to work fine. somehow I need to switch the direction , I guess I need 65500 for TOGO and ZERO for Idle position right? How can I switch that?

best
Stefan

One more question though, I am using the BU0836X for inputs and the opencockpits output card with SIOC for LED outputs, but I ran into one small issue. There is not an offset for SPD, HDG, VSI and ALT inc and dec, therefore I cannot assign it through FSUIPC. Any ideas on how to make this work?
I read a post about using the "data pipe" but the post is a little vague, and the user guide does not have the info on data pipe. Is there another manual that explains this issue better?


Jose

Hi Jose,

the BU0836X is a joystick board from the computer point of view. Do not ust FSUIPC to assigne actions to joysticks buttons, instead use the FMGS_Config.exe application, there you'll find a "buttons" window where you'll be able to do that.

As for the opencockpit card, you should not use FSUIPC with your own script code, instead uise SIOC Creator (it is installed when you select "SIOC support" during installation).

Regards,
JL

Thank you very much JL, I will try the FMGS_config to configure the buttons, as for the SIOC creator, that is what I'm using to create the code for the output card. Again, thank you very much for the reply.

Respectfully,

Jose

Prepar3d 2.3 is out -- some notable performance improvements. I will test it out with FMGS and see how it goes.

For those installing 2.3, you need to update to the latest FSUIPC beta -- http://fsuipc.simflight.com/beta/FSUIPC4934h.zip

Hi all

found the error..... had the handle installed to hold all 3 levers, so it recognized all of them. deinstalled handle and used just one lever, and it works... grrrrrmph.

Best
Stefan

Hi guys, JL,

Thanks for the help with the FMGS_config, I have everything working, but I have a new issue that just started, after takeoff the plane begins to oscillate up and down from its axis, and it even continues the oscillation with the AP on, it only stops when it is on a climb on "OP CLB" any other type of climb produces the oscillation.

Jose

Jose, do you uses the aircraft addon distributed (and installed directly into FS/P3D) by my software?
Do you use fixed FPS settings? The software requires FPS steady at above 25FPS.

JL