Printable View
Hello Jeehell.
I tryed with FSUIPC 4.60a but without sucess again. With this version if I close AP.FBW.exe I can move ailerons and acelerate aircraft, if I run AP.FBW.exe the the throtlle move in E/WD but dont acelerate the aircraft, the fcu dont control the aircraft and joystick dont move the ailerons, ruder or others superficies.
I think that exist disconnection between AP/FBW and FSUIPC or other. This capture the signal but dont transmit.
Can you help?
Regards
LM
Hello,
All I can tell you right now is to wait for next version, it will come out soon (probably tomorrow). I completely changed the joystick and analog axis system.
JL
Hi all,
I just finished the B17 version.
I completely reworked the joysticks/THR LVR logic.
Now you need to use an external software to assign the joysticks to use in the FMGS, it's called FMGS Config.exe, and is located in the FMGS Server folder.
It adds support for the dual stick (but not priorities yet).
I also tried to correct a few other bugs, check the readme/manual for more info!
This is still quite experimental, you may experience some troubles with it so be careful to keep the previous version!
And as usual bug reports are welcome!
The link: http://www.jeehell.org/A320FMGS_B17.zip
Cheers,
Jean Luc
Hi again!
I think that my problem is in FSUIPC, You are right, the version 4.30 or before not work, with 4.60a in my last tests I had positive results.
I will continue with more tests and I tell you something later.
Regards
LM
Aeropt: ok good to hear.
For everyone, it seems the B17.1 OVHD is bugged, you can use the B17.0 one as it is 100% compatible; I'll try update a fix tomorrow.
JL
Thank You JL.
Hi,
Just corrected the ovhd bug along with a couple small bugs.
Same link as previous release:
http://www.jeehell.org/A320FMGS_B17.1.zip
JL
Hello…
Firstly I would like to say one thing to J.L : CONGRATULATIONS FOR ALL YOUR WORK !!!
I’m a French new user who discovered B16.2 version yesterday…
I was told today about the B17.1 and downloaded it on this afternoon.
I’m not very used with the software, and the French Guide is very useful for me.
I run AP/FBW and FMGSServer on my FSX computer (Windows 7 64 bits / FSUIPC 6.4).
OVHD is installed on another PC (WinXP + latest Wide FS),
Captain PFD/ND works on a third PC (WinXP + latest WideFS)
Here are my tests :
FSX is running ; as soon as I run OVHD, the IFDG A320 reactors stop : okay, OVHD is rightly connected to FSX.
As soon as I select BATT to put ELEC ON, I got this error message on the OVHD PC : “Access violation of address 00000000. Read of address 00000000”.
Then I launched FMGSServer and got the following : “Access violation of address 0053AB04 in module FMGSServer.exe . Read of address 00000000”.
Are these some results of wrong actions from me, or are these bugs ?
Regards.
Michel.
P.S : I hope that this message will be correctly posted (I was rejected at 3 times after writing, with “you are not logged” messages…)
Hi Michel,
First welcome here ;)
Concerning the OVHD error, I've just corrected it, download the package again: http://www.jeehell.org/A320FMGS_B17.1.zip
As for the FMGS Server one, the most probable cause is you didn't configure your joysticks with FMGS config prior to launching the server?
I also have received your mail, I'll answer to you right away:
Cheers,
JL
Hi J-L !
Thank you...
Effectively, OVHD works right with this new version just downloaded.
About FMGSconfig, OUPS ! I only missed it, I didn't remember it in the B16 version...
Now I've set my old Logitech joystick and it's small potentiometer...
No more error messages at this time : I've just started my 2 reactors on, with OVHD, and all seems to work right ! It's a nice beginning !! :-D
PFD and ND are working too, on the third PC...
Let's see tomorrow for AP and other settings
Good night,
Michel