SIOC Problems

Hi Hessel,

As previously mentioned I personally do not understand the whole nature of the Opencockpits Manuals, and thus could not deduce what to write.

As I also wrote in the other page, Nico's site is a BIG help to me but I still need a bit of extra assistance to get things working - That's just how I am I'm afraid, and I can't help that until I get tha hang of SIOC.

I also said that I have read through most of the Opencockpits documentation that I could find, including two presentations.

I would not post here if I knew how to do it beforehand.

Thanks,

Jack =)

Jack,

As mentioned before, on the HOW TO page it is written to the last digit ...:-)

http://www.lekseecon.nl/howto.html#readFSUIPC

Quote:

---

Var 1 Link FSUIPC_IN Offset $0BC8 Length 2 // parking brake state
{
IF v1 = 0
{
v2 = 0
}
ELSE
{
v2 = 1
}
}

Var 2 Link IOCARD_OUT Output 91 // led indicating parking brake set

---

This is *exactly* you were asking, isn't it ?

H.

Oh dear... Another problem.

What is wrong with the following script:

Code:

---

Var 9000 Link IOCARD_SW Input 12 Type P
{
v9001 = V9000
}
Var 9001 Link FSUIPC_OUT Offset $07BC Length 4

Var 1 Link FSUIPC_IN Offset $07BC, Length 4 // AP MASTER STATE
 {
  IF v1 = 0
  {
    v2 = 0
  }
  ELSE
  {
    v2 = 1
  }
 }

 Var 2 Link IOCARD_OUT Output 23 // AP MASTER LED

---

And SIOC.ini:

Code:

---

[SIOC]
IOCP_port=8092
IOCP_timeout=4000
Minimized=Yes
toggle_delay=20
CONFIG_FILE=LEDtest.ssi

[IOCARDS MODULE]
IOCard_disable=No
IOCard_LPT=No

[MASTERS]
MASTER=0,11,1,69

[FSUIPC MODULE]
FSUipcdisable=No
FSUipcRefresh=50

[IOCP CLIENTS MODULES]
IOCPini_delay=3000
IOCPclient0_disable=Yes
IOCPclient0_host=localhost
IOCPclient0_port=8090
IOCPclient1_disable=Yes
IOCPclient1_host=localhost
IOCPclient1_port=8099

[SOUND MODULE]
Sound_disable=Yes
Volume=100

---

And SIOC Interface screen:

http://i822.photobucket.com/albums/z...pheric/yut.jpg

The SIOC file I'm running is obviously LEDtest.ssi

After consulting the SIOC manual I'm still lost, I must've missed something.

Thanks alot, forgive my (potential) ignorance,

Jack

Jack,

you've got two definitions for the same FSUIPC offset $7BC: one a FSUIPC_IN link and the other a FSUIPC_OUT link. Change one to FSUIPC_INOUT and delete the other.

FSUIPC_INOUT is not well documented by OC but it is in SIOC tutorial 1

Jim

Jack,
Are you sure that at output 23 there is a led?
Nico
P.S. we should re-phrase the topic of this thread: it is not about problems in or with SIOC but about learning SIOC :-)

Quote:

---

Originally Posted by deering

you've got two definitions for the same FSUIPC offset $7BC: one a FSUIPC_IN link and the other a FSUIPC_OUT link. Change one to FSUIPC_INOUT and delete the other.

---

Athough Jim is right I do not think that this is the problem. It is perfectly allright to have as well an FSUIPC_IN as a FSUIPC_OUT variable to the same offset in one script.

Right again, Nico.

Thx

Hi Nico,

Yes there is an Output on LED 23.

I think the problem moreover is that the AP MASTER Switch does not come on at all in-sim.

Hi all!

May I jump in with another SIOC question:

When starting Controlador.exe, an error message about IO.DLL pops up. It says 'Unable to start the IO.SYS service. Error code = 1275'.

Clicking OK to accept the info, closes the error message and opens Controlador application which works just fine, as does SIOC.EXE!

Anyone understanding the implication of this error?

Volante

Hello everyone,

Just wondering has anyone managed to figure out wh ythat SIOC script doesn't work, the push button isn't even detected by the AP Switch.