A320 FMGS B46

Hi Jeddmc,, what motherboard are you using ? I 've chosen to use 3 computers (server + 2 clients) .
The server pc runs P3d, AS16 + ASCA and a part of skalarki hardware. 1 client pc for PFD ND e FMGS for CPT and FO and the remaining part of skalarki hardware.The 2 client pc for ECAM displays. I've chosen this configuration because I had problems with usb ports to connect all skalarki hardware.
Cheers
Ben

Quote:

---

Originally Posted by digidax

Fritz, what simulator do you use? FSX or P3D?

best regards, Frank

---

I have opened a thread related to this post.

http://www.mycockpit.org/forums/show...466#post165466t

Hi Jl!

Before I'm going to start cabling my ACP Panels, I would like to ask if you are planning to enhance the SIOC interface with ACP Inputs and Outputs (via SIOC-Creator)?
The potentiometers I will connect via Joystick-Axis.
Alternatively I can connect all buttons and switches via Joystick Buttons as they arealready configurable in FMGS-Config.
But what is you plan in regards of the green Button-LEDs and white CALL-LEDs ... ?

Thanks!
Christian

Hi

Yes I will add support in SIOC for the ACP at some point, not sure when yet...

JL

Last weekend I tried to use the flightmodel from the previous release to solve the oscillations problem at cruising altitude.
At cruising altitude the plane hold constantly the cruising altitude, no more oscillations.
Some minuites later P3D hang up. I also had no flightpath on the ND.
The using of flightmodel from previous release is also not a solution.
I decide to wait for JeeHells next update.

Quote:

---

Originally Posted by navigator88

Hi Jeddmc,, what motherboard are you using ? I 've chosen to use 3 computers (server + 2 clients) .
The server pc runs P3d, AS16 + ASCA and a part of skalarki hardware. 1 client pc for PFD ND e FMGS for CPT and FO and the remaining part of skalarki hardware.The 2 client pc for ECAM displays. I've chosen this configuration because I had problems with usb ports to connect all skalarki hardware.
Cheers
Ben

---

Hi...i'm using Gigabyte Z97X
i use three usb hub with power which mean i can have extra 9 usb port for all hardware

Quote:

---

Originally Posted by jeddmc

Hi...i'm using Gigabyte Z97X
i use three usb hub with power which mean i can have extra 9 usb port for all hardware

---

Thanks for your reply.
Just to be sure about the model you have. Is it perhaps the Gigabyte Z97X gaming 3,5 or7?
Do you have skalarki usb hardware connected on your 3 usb powered hubs?

All my best
Cheers
Ben

Quote:

---

Originally Posted by navigator88

Thanks for your reply.
Just to be sure about the model you have. Is it perhaps the Gigabyte Z97X gaming 3,5 or7?
Do you have skalarki usb hardware connected on your 3 usb powered hubs?

All my best
Cheers
Ben

---

its Z97X gaming 7
i'm using fds hardware

Quote:

---

Originally Posted by jeddmc

its Z97X gaming 7
i'm using fds hardware

---

Thank you so much.
Ben

Quote:

---

Originally Posted by Fritz

Last weekend I tried to use the flightmodel from the previous release to solve the oscillations problem at cruising altitude.
At cruising altitude the plane hold constantly the cruising altitude, no more .
Some minuites later P3D hang up. I also had no flightpath on the ND.
The using of flightmodel from previous release is also not a solution.
I decide to wait for JeeHells next update.

---

I had the same oscillations problem with Build 46 / P3D 3.4..... Solved with moving C.G. a little bit forward.


Cheers
Daniel