Stefan, what is your complete setup?
Printable View
Stefan, what is your complete setup?
Hi all,
Another update available on the automatic updater. It corrects WideFMGS and CPFlight module bugs.
Best regards,
JL
Hi JL
It works now after a clean reinstallation. Sorry :oops:
Hello JL,
have problems to start the updater.exe on the FSX pc. It says: service under maintenance. The member pc's are able to update without any problems.
Cheers
Stefan
Hi JL,
some things I noticed lately. The first issue is new with b28.
- when you enter a DIRECT TO the route from the TP point is not displayed anymore. To be honest: I have no clue what should be displayed in that case and if a temp point is created. Anyhow --> when entered a direct to the time and distance to the next waypoint is not updated correctly. After pushing DIR TO the first initial waypoint of the original route is displayed on the upper right ND, not the selected DIR TO waypoint. Take a look --> you will see what I mean
- MW bell and MW korry light coordination: There seems to be a tiny logic bug. Imagine you have two master warnings at the same time (i.e. parking brake set and no flaps for takeoff). Now you push the MW korry in b28. Then the bell continues due to second MW but the flashing red light remains off. You need a second push to cut off the bell, even the korry is not flashing anymore.
I assume a single MW korry push should be sufficient to quit both or to have lights and bell twice for both warnings, right?
- sometimes the manual entries for SPD or ALT restrictions are not correctly updated on the FPLN page.
- In case you enter a SPD or ALT restrictions which cant be performed what should be the feedback to the pilot?
- Have you touch V-NAV with b28? Just curious?
Thanks & regards!
Rob
Hi Jh,
I installed the new Vers 28.3, and Have a two problem...... I think...
1-- The EWD display show the epr gauges, and the luminosity is low..
2-- The Sd display show only the temperature... no more page is show.
its a change to N1 EPR version in cgf file?
and inSd display ?
Many tanks
Daniele
Well done JL, I was sure you would did it... First whole perfect flight since B.26
Only minor issues for me at the moment:
1. Auto brake doesn't turn off after manual braking
2. PFD (both CPT-FO) run with low performance. Tapes (SPD-ALT) do not roll, but jump if you get what I mean.
3. This version is not compatible with previous seved PILOT ROUTES, is it?
Thanks for all
Hi,
First there is a new WideFMGS version available on the updater. Two important nootes:
- it seems to be necessary for now to start the server first, and then the clients. I'm working on that
- The updater seems to refuse two or more downloads at the same time from the same IP, so if you have issues, download on each computer one at a time...
@Stefan: in the installation folder, please remove any file called version.txt or completeversion.txt or version2.txt. If it still does not work, it could be connection or a firewall issue.
@Rob:
-ND issues: probably linked to WideFMGS.
-MW: I'll have a look when this widefmgs thing is over...
-same
-there should be an amber circle around the point on the ND (not modeled yet) and an amber star on the MCDU (modeled)
-nope
@Daniele: hopefully your issues are gone with current update... the EPR version is still NOT available, and won't be for a long time.
@Leonidas:
-Strange, you configured braking axisd through FMGS config??
-Should be corrected with this update
-it should be compatible. But there are some issues with CO/PIL RTEs sometimes...
Cheers,
JL
Thank you...
Hi JL,
again FW, grrrrrrr. Thanks. All works fine for now :-). Very good job !!!
Cheers Stefan