Printable View
I did check again out of curiosity, and everything works correctly. When changing the location, the UTC time does not change and stays at the UTC time of P3D when first launched (+/- a few minutes due to loading scenery etc...).
So I will not waste my time further on that non issue...
JL
My UTC time works correctly.
For the Landing checklist showing up after takeoff, I will check again on some other flights. Yesterday I made LOWW Vienna to Innsbruck LOWI with same MCDU programming's procedure and Ecam works fine. (except entering Destination WX data)
Oh, maybe on last VVTS-VVDN flight, I entered Destination data (QNH, Temp, Wind) at departure airport, that caused MCDU considering we are on landing phase :D ?
Thanks,Vu
Hallo JL,
Sorry if I offended you. If FMGS is connected before I change airport to VVTS then UTC does not change as you stated. However, if I change the airport after a restart of P3D then UTC is not correct. I double-checked this again this morning.
Best regards,
--pim
@Masterp: the arrival data shuld not be the reason you have the LDG checklist on display, unless you switched on the APPR PHASE manually in the MCDU?
@Pim: this is not about any offence... it just works. I do not understand your steps to supposedly reproduce any bug with UTC time. Try this other way: in P3D go to world menu -> time and season. And set the UTC (or even local time) yourself there and compare with what you should get...
My sofware reads the UTC time P3D gives, no more no less. If P3D is not synchronized with actual UTC time, then it will display a non-synchronized time... Particularly, loading a flight may desynchronize the time...
JL
Hi JL i ve just made another flight VVVH VVNB and LDG checklist was not shown up on departure.
However try again with VVTS VVDN route, LDG checklist showing up a few seconds then back to normal :mrgreen:
So i suggest to ignore this, it just random. Thanks for your help. Vu
Aerosoft Airbus X AIRAC cycle within Navdata1 and Navdata2 1508 installed ..
Navdata1: PROC-Airports-throw-cycle-cycle-info-navaid waypoints
Navdata2: PROC-Airports-throw-cycle-cycle-info-navaid waypoints
Home on my computer, prepar3d FMGS server and A320 have 2.5 installed.
Second on my computer, FMGS A320 wide client installed.
I start my main computer, and then the A320 Simulator FMGS.
Everything is going great.
Second on my computer, I start FMGS A320.
Batteries çalıştırıyorum.sist comes up full of energy.
But MC "Active Base data NAV" 0000
Second NAV 0000 data base.
LTBI / LTCG FROM / TO NOTE IN DATA BASE LKS1 error.
Hello,
Aerosoft Airbus X AIRAC cycle within Navdata1 and Navdata2 1508 installed ..
Navdata1: PROC-Airports-throw-cycle-cycle-info-navaid waypoints
Navdata2: PROC-Airports-throw-cycle-cycle-info-navaid waypoints
Home on my computer, prepar3d v2.5 and A320 FMGS server have installed.
Second on my computer, FMGS A320 wide client installed.
I start my main computer, and then the A320 Simulator FMGS.
Second on my computer, I start FMGS A320. Batteries .sistems comes up full of energy.
But MC "Active Base data NAV" 0000
Second NAV 0000 data base.
LTBI / LTCG FROM / TO NOTE IN DATA BASE LKS1 error.
And why on earth do you install AS Airbus X AIRAC with A320FMGS and not the database for Jeehell?Quote:
Originally Posted by yaarslan
Make sure your throttle detents and dead zones are setup correctly. When my dead zones were too small I triggered the LDG checklist for some reason.Quote:
Originally Posted by masterp
I have a problem with the nose wheel steering. If I give a little thrust, then the nose wheel always moves to the left. I have adjusted the tiller and flight stick several times. On the flight control page I cannot realize that something steers to the left. With the tiller I can correct a maximum to the center position. After I steer the Airbus in the trees, P3D loaded the default Cessna - the same phenomenon. In P3D without FMGS I can easily control the nose wheel. It seems the problem is not caused by aircraft model or P3D. Anyone had the same problem?