Standard barometric button

[Tom Stian Bjerk]

Hi..


With the build 435 of the MCP I could see in the GC what pressure I have
adjusted it to when I pushed the Standard barometric button. But now with
the 435a build the GC only show STD.

Hope you understand me :)

What is the correct behavior? :)

Best Regards
Tom Stian Bjerk

[Enrico Schiratti]

Are you using any hardware for the MCP?

"Tom Stian Bjerk" wrote in message
news:383761.77029@wb.onvix.com...
> Hi..
>
>
> With the build 435 of the MCP I could see in the GC what
> pressure I have
> adjusted it to when I pushed the Standard barometric
> button. But now with
> the 435a build the GC only show STD.
>
> Hope you understand me :)
>
> What is the correct behavior? :)
>
> Best Regards
> Tom Stian Bjerk
>

[Tom Stian Bjerk]

Using only your software.. No hardware

Best Regards
Tom Stian Bjerk

[Bill Trinidad]

Question : Will the baro button and settings on the Aerosoft MCP EFIS (
although I fly a 737 ) behave as if it were a 737 EFIS ?

I am not able to achieve the operation as described in a much earlier post.

I cannot get a "standby" setting to appear while in STD mode at the flight
levels.

Bill T.




"Tom Stian Bjerk" wrote in message
news:384378.77029@wb.onvix.com...
> Using only your software.. No hardware
>
> Best Regards
> Tom Stian Bjerk
>

[Enrico Schiratti]

> Question : Will the baro button and settings on the
> Aerosoft MCP EFIS (
> although I fly a 737 ) behave as if it were a 737 EFIS ?

No, it won't. I will try to look into it, but can only do it
for the serially connected version.

Ciao

Enrico

[Enrico Schiratti]

Ok,

I checked things, and there are two possibilities... the
temp value is only shown if you change it... did you try
that? Also, do confirm it is set to Captain if you are
changing it on the captain side EFIS.

There has been no change to the code in the a build.

Ciao

Enrico

"Tom Stian Bjerk" wrote in message
news:384378.77029@wb.onvix.com...
> Using only your software.. No hardware
>
> Best Regards
> Tom Stian Bjerk
>

[Bill Trinidad]

Yes, changed altimeter using baro knob, did not observe any other numbers
under STD *window*.

gc.ini set to Copilot = Off

mcp.ini has no value under [serial connection], Aerosoft MCP plugged into
COMM 1.


"Enrico Schiratti" wrote in message
news:385194.77029@wb.onvix.com...
> Ok,
>
> I checked things, and there are two possibilities... the
> temp value is only shown if you change it... did you try
> that? Also, do confirm it is set to Captain if you are
> changing it on the captain side EFIS.
>
> There has been no change to the code in the a build.
>
> Ciao
>
> Enrico
>
> "Tom Stian Bjerk" wrote in message
> news:384378.77029@wb.onvix.com...
>> Using only your software.. No hardware
>>
>> Best Regards
>> Tom Stian Bjerk
>>
>

[Enrico Schiratti]

My message was in reply to Tom, with The Aerosoft MCP I will
look into implementing it for the serial communication part
if it is possible.

Ciao

Enrico


"Bill Trinidad" wrote in message
news:385215.77029@wb.onvix.com...
> Yes, changed altimeter using baro knob, did not observe
> any other numbers
> under STD *window*.
>
> gc.ini set to Copilot = Off
>
> mcp.ini has no value under [serial connection], Aerosoft
> MCP plugged into
> COMM 1.
>
>
> "Enrico Schiratti" wrote in message
> news:385194.77029@wb.onvix.com...
>> Ok,
>>
>> I checked things, and there are two possibilities... the
>> temp value is only shown if you change it... did you try
>> that? Also, do confirm it is set to Captain if you are
>> changing it on the captain side EFIS.
>>
>> There has been no change to the code in the a build.
>>
>> Ciao
>>
>> Enrico
>>
>> "Tom Stian Bjerk" wrote in message
>> news:384378.77029@wb.onvix.com...
>>> Using only your software.. No hardware
>>>
>>> Best Regards
>>> Tom Stian Bjerk
>>>
>>
>

[Bill Trinidad]

Enrico,

OK, I now have a reason as to why I'm not getting the info on my Aerosoft
MCP.

Thanks for the clarification,

Bill T.


"Enrico Schiratti" wrote in message
news:385219.77029@wb.onvix.com...
> My message was in reply to Tom, with The Aerosoft MCP I will
> look into implementing it for the serial communication part
> if it is possible.
>
> Ciao
>
> Enrico
>
>
> "Bill Trinidad" wrote in message
> news:385215.77029@wb.onvix.com...
>> Yes, changed altimeter using baro knob, did not observe
>> any other numbers
>> under STD *window*.
>>
>> gc.ini set to Copilot = Off
>>
>> mcp.ini has no value under [serial connection], Aerosoft
>> MCP plugged into
>> COMM 1.
>>
>>
>> "Enrico Schiratti" wrote in message
>> news:385194.77029@wb.onvix.com...
>>> Ok,
>>>
>>> I checked things, and there are two possibilities... the
>>> temp value is only shown if you change it... did you try
>>> that? Also, do confirm it is set to Captain if you are
>>> changing it on the captain side EFIS.
>>>
>>> There has been no change to the code in the a build.
>>>
>>> Ciao
>>>
>>> Enrico
>>>
>>> "Tom Stian Bjerk" wrote in message
>>> news:384378.77029@wb.onvix.com...
>>>> Using only your software.. No hardware
>>>>
>>>> Best Regards
>>>> Tom Stian Bjerk
>>>>
>>>
>>
>

[Tom Stian Bjerk]

Yes, I can see the value when I changing it now.. So there is no bug.. Only

me I think :=)
But I dont know why it works now. I will report it again if I get the same
problem :)

Best Regards
Tom Stian Bjerk


"Enrico Schiratti" wrote in message
news:385194.77029@wb.onvix.com...
> Ok,
>
> I checked things, and there are two possibilities... the
> temp value is only shown if you change it... did you try
> that? Also, do confirm it is set to Captain if you are
> changing it on the captain side EFIS.
>
> There has been no change to the code in the a build.
>
> Ciao
>
> Enrico
>
> "Tom Stian Bjerk" wrote in message
> news:384378.77029@wb.onvix.com...
>> Using only your software.. No hardware
>>
>> Best Regards
>> Tom Stian Bjerk
>>
>