Server error help needed

[sxa1376]

Dear JL,

I am facing since the version 49.0 a problem with the server. After i am load a flight and i run the "StarterENGRUN.exe"
the server is running and its all connected fine but after some seconds the server crashes and i am getting the following
error:



Any ideas of how i can solve this?
Many thanks in advance.
I am using p3d v3.4

[sxa1376]

I did a complete unistall and reinstall everything and the same problem again.
As i noticed it might be the perfomance folder causing te problem.
I have create an a321 cfm based on pa model and in order for this to work i edit the
"Folders.ini" and i have add a new section. also i have create a new folder for my aircraft and
inside this folder i have edit the "aircraft.ini" with the new values. Also i have put the folder of the aircaft inside
the "A320FMGS\Aircraft" instead of the "p3d\simobjects\airplanes" .
I attach the two files i think they causing the problem. Any help will be great.


Folders.ini:

[General]
NbOfACFT=3
ACFT.1=CFM
ACFT.2=IAE
ACFT.3=A321
PIDlist=yes

[ACFT.1]
PERF_Folder=CFM
EnginesType=CFM56-5B4



[ACFT.2]
PERF_Folder=IAE
EnginesType=V2527-A5


[ACFT.3]
PERF_Folder=A321
EnginesType=CFM56-5B3




aircraft.ini:

[AIRCRAFT]
StatusTitle=A321-211
EPR/N1=N1
Baro=mb
VFE_1=230
VFE_1+F=215
VFE_2=215
VFE_3=195
VFE_4=190
VLE=280
flaps_position.0=0
flaps_position.1=0
flaps_position.2=10
flaps_position.3=14
flaps_position.4=21
flaps_position.5=25
slats_position.0=0
slats_position.1=18
slats_position.2=18
slats_position.3=22
slats_position.4=22
slats_position.5=27
delta_RadioAltitude=12
MaxOilPressScale=100
IncreasingHighOilPressPulse=90
DecreasingHighOilPressPulse=85
IncreasingLowOilPressPulse=20
DecreasingLowOilPressPulse=16
RedLowOilPress=13
IncreasingHighOilTempPulse=140
DecreasingHighOilTempPulse=135
HighOilTempAmber15min=140
HighOilTempAmberImm=155
QFEoption=yes
INITBaccessible=yes
AFTcargoVent=yes
AFTcargoHeat=yes
FWDcargoVent=yes
FWDcargoHeat=yes
Spacing833=yes
LinkISISQNHtoCPT=yes
MMO=0.82
VMO=350
EISmodel=1
midscaleEGT=500
maxscaleEGT=1000
MaxEGTred=950
MaxEGTamberTO=725
MaxEGTamberCRZ=915
aircraft.cfg=A321-211\aircraft.cfg
airfile=A321-211\CFM56-5B3.air

[jeehell]

It could be an error in the aircraft.Cfg.
The error message you have says '780' is not a valid integer, notice the space character (underlined) after 780. See in you A321 aircraft.cfg is you did not leave a space at the end of a line somewhere...

[sxa1376]

Thank you very much jeehell for your awnser, i searched the files and i found were the space was.
Now it is working fine!!!