fliegster
04-03-2016, 03:47 PM
Good afternoon all,
My first time posting, and I'm happy to begin taking steps to maximizing the realism of my flight simulator. I particularly enjoy flying the 777 in p3d.
To that end, I have taken steps to secure a 777 looking throttle quadrant, which is probably not the most accurate representation of the true TQ, but it could serve if I took some steps to amend some particularly frustrating issues, which is the reason I am posting this message.
Currently, the TQ is OK, but some of the issues I continually face is that on some days button switches work and on other days they simply do not (clicking the button is simply not recognized in the joystick calibration screen on some days, which is very bizarre). Additionally, all three axes (2 throttle 1 flap) are very "noisy," meaning when I accelerate the throttle for example, I see noise in the calibration screen and the signal jumps all over the place - i.e. it's not a smooth linear acceleration. It's gotten to the point where I am too nervous to use the TQ during a VATSIM event because I fear the flaps would perhaps erroneously deploy or the fuel cutoff switch would reset itself. Just in general, there is a lot of "noise" with the buttons and axes. I took steps to disassemble the TQ, here is a picture:
http://www.mycockpit.org/forums/attachment.php?attachmentid=11383&stc=1
It's an utter mess inside there, and anytime I put my hands near the cable / wiring or touch ANYTHING, all the buttons / axes jump around in the calibration screen. What should my next steps be concerning getting this TQ fully operational and reliable? I.e. no control spikes, etc. I'd like to solicit the opinions of anyone on this board to provide some meaningful advice in terms of some realistic next steps. The worst part concerning this endeavor is that I know NOTHING about electricity, or wiring, for that matter. Are there any useful books or online guides I could read to become acquainted with how these types of electrical interfaces work? I know it cannot be at all that difficult, just need to know what the goal is, and perhaps learn how to sodder.
The IO card inside is from a joystick Logitech 3...
Thanks to anyone who can offer up any help.
Regards,
Robert
My first time posting, and I'm happy to begin taking steps to maximizing the realism of my flight simulator. I particularly enjoy flying the 777 in p3d.
To that end, I have taken steps to secure a 777 looking throttle quadrant, which is probably not the most accurate representation of the true TQ, but it could serve if I took some steps to amend some particularly frustrating issues, which is the reason I am posting this message.
Currently, the TQ is OK, but some of the issues I continually face is that on some days button switches work and on other days they simply do not (clicking the button is simply not recognized in the joystick calibration screen on some days, which is very bizarre). Additionally, all three axes (2 throttle 1 flap) are very "noisy," meaning when I accelerate the throttle for example, I see noise in the calibration screen and the signal jumps all over the place - i.e. it's not a smooth linear acceleration. It's gotten to the point where I am too nervous to use the TQ during a VATSIM event because I fear the flaps would perhaps erroneously deploy or the fuel cutoff switch would reset itself. Just in general, there is a lot of "noise" with the buttons and axes. I took steps to disassemble the TQ, here is a picture:
http://www.mycockpit.org/forums/attachment.php?attachmentid=11383&stc=1
It's an utter mess inside there, and anytime I put my hands near the cable / wiring or touch ANYTHING, all the buttons / axes jump around in the calibration screen. What should my next steps be concerning getting this TQ fully operational and reliable? I.e. no control spikes, etc. I'd like to solicit the opinions of anyone on this board to provide some meaningful advice in terms of some realistic next steps. The worst part concerning this endeavor is that I know NOTHING about electricity, or wiring, for that matter. Are there any useful books or online guides I could read to become acquainted with how these types of electrical interfaces work? I know it cannot be at all that difficult, just need to know what the goal is, and perhaps learn how to sodder.
The IO card inside is from a joystick Logitech 3...
Thanks to anyone who can offer up any help.
Regards,
Robert