View Full Version : FS BUS boards
marmaris2014
01-31-2014, 05:25 PM
Hello
I'm having FSBUS card I can use them in other software do you have?
Jan737
02-01-2014, 03:58 AM
Simple answer:no
Regards
Jan
marmaris2014
02-01-2014, 05:33 AM
Thanks JAN
How could for PMGD NG
Jan737
02-01-2014, 06:46 AM
If you know the offsets for the PMDG NG you can declare them in the FSbus software and use the fsbus cards.
Google PMDG NG offsets or find out here on the forum
Good luck
Jan
marmaris2014
02-01-2014, 08:07 AM
Thank you very much Jan:)
marmaris2014
02-01-2014, 10:32 AM
Could you write an example for pmdg NG.
I'm using FS2004
marmaris2014
02-05-2014, 03:53 PM
can I use the joystick button key cards as FSBUS
rtszkrsn
02-05-2014, 04:38 PM
https://www.facebook.com/rtszkrsn eklermisiniz
Jan737
02-06-2014, 01:15 PM
What version of FSbus software are you using?
Reed the documents who comes with the software installer.
You must change the default (FS2004) offsets with the PMDG offsets.
Goodluck
Jan
marmaris2014
02-06-2014, 02:24 PM
Thanx Jan
I'm using FSBUS 2.4
But I could not find on the inernet PMDG ng ofset.
seanatp
02-06-2014, 02:48 PM
Hi guy's could you please let me know where I can find all the info on the diff FSBUS cards. I would like to build my own cards but can't find any info on them or any PCB designs? I am new to this.
Thx
Sean
marmaris2014
02-06-2014, 06:02 PM
I have FSBUS Board PCB and schemma.I can send in your mail
seanatp
02-06-2014, 06:25 PM
Yes please my mail is: seanatp1@gmail.com please thanks for the help
marmaris2014
02-06-2014, 07:36 PM
Please check your e mail
Jan737
02-07-2014, 04:14 AM
I don't use the PMDG, so I couldn't help you with that
Jan
seanatp
02-07-2014, 06:50 AM
Thx man this is gr8t!! I will push on your button again once I need to start using them hehe. Thx man
Sean
seanatp
02-07-2014, 07:12 AM
Thx man this is gr8t!! I will push on your button again once I need to start using them hehe. Thx man
Sean
You don't have any documentation on these cards parts list an so on? I'm also looking for the FSBus IO Card? If you don't have this could you steer me in the right direction maybe?
thx Sean
Jan737
02-07-2014, 04:04 PM
The version 2.4 is a old version. There is a new software version and pcb boards available at: http://www.rvdijk.nl
Take a look, it's a great site about the fsbus stuff.
Jan
gaitflight
02-08-2014, 06:01 PM
go to www.fsbus.de (http://www.fsbus.de) for version 3.0.2
when you have install this then you look in the installed map
thereare the drawings
greets from gaitflight
www.gaitflight.nl (http://www.gaitflight.nl)
seanatp
02-09-2014, 04:33 PM
Thank you all for your help!!
Just another question the micro controllers do they get programmed after you build the boards by the FSBus program once you plug the boards into the PC or do you have to program them before installing them with a micro controller programer?
thx
Sean
Jan737
02-10-2014, 01:11 PM
Sean,
There is an onboard 6 pin ISP on the com. board to program all the different Atmel controllers. So first build the com board.
Regards
Jan