Page 4 of 7 FirstFirst 1234567 LastLast
Results 31 to 40 of 61
  1. #31
    300+ Forum Addict
    Join Date
    Mar 2007
    Location
    Norway
    Posts
    415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Your seat is looking very nice BSW. You are doing very good work and you obviously do alot of research to get it as real as possible.

    I love it

  2. #32
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks! I found these brackets in my shop. I don't remember what they were for, but I made good use of them for my chair supports. Now I can add some additional support members to try and replicate the rest of the suspension system.

    It's bolted down to the 2x4's because it was still an 1-1/2" too short. It's right at 22" at the knee bend now. Right where I need it.



    The inertial reel shoulder harness I purchased from Nick at APHS:

    Last edited by Michael Carter; 08-18-2007 at 01:35 PM.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  3. #33
    500+ This must be a daytime job JBaymore's Avatar
    Join Date
    Mar 2005
    Location
    Wilton, New Hampshire USA
    Posts
    601
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Not to pry too much... and you DON'T have to answer this ... just ignore it.... but what kind of price (ballpark) are you talking about on that shoulder harness setup?

    Thanks either way.

    best,

    ..............john

  4. #34
    http://www.angelfire.com/il2/aphs/forsale/forsale.html

    Not bad considering brand new these things are up towards the $1000 dollar mark.

    Gary

  5. #35
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    $80 with shipping. Brand new in the box.

    With a little patients, I hope to have my seat looking better than those. Even if they are the real Webers.
    Last edited by Michael Carter; 08-18-2007 at 02:11 PM.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  6. #36
    $80 bucks brand new.... wholely smokes... You would be gobbsmaked with the price of the recent purchase order we just made for 3 of these things from Pacific scientific. Nick is certainly a great asset to this hobby thats for sure.

    Gary

  7. #37
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I would't be as far as I am without him, or Bill and Snap at e-Bay.
    Last edited by Michael Carter; 08-18-2007 at 10:02 PM.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  8. #38
    75+ Posting Member James Twomey's Avatar
    Join Date
    Jan 2007
    Location
    Port Orchard Wa, U.S.
    Posts
    119
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Well, I have to add my two cents worth here! That is NICE work! Once I get done building my own throttles, I might have to have a go at my seats. Once again, NICE!

    James

  9. #39
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Those belts will stop you falling out of the chair drunk! That's a good thing about simming, no 8 hours from bottle to throttle - into it. All Aussie sims are built with beer holders obviously, the trouble is I keep falling asleep at the wheel and usually wake up to the spool down sounds when I'm out of gas somewhere totally lost!

    Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  10. #40
    75+ Posting Member James Twomey's Avatar
    Join Date
    Jan 2007
    Location
    Port Orchard Wa, U.S.
    Posts
    119
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    oh my GAWD.....I dont have belts.......have had plenty of beer though!!!!!!

Page 4 of 7 FirstFirst 1234567 LastLast

Similar Threads

  1. 737 Crew Seat
    By droddis in forum Where to Start Building a Home Cockpit
    Replies: 6
    Last Post: 06-07-2012, 02:58 PM
  2. [Discussion] Multi Crew Cockpit VS Single seat Cockpit !!
    By SU-GGG Dispatcher in forum Cockpit Parts and Motion Platforms
    Replies: 1
    Last Post: 11-14-2010, 04:22 AM
  3. Which car seat could make a good platform for a 737NG seat ?
    By Nick1150 in forum Cockpit Parts and Motion Platforms
    Replies: 4
    Last Post: 07-29-2010, 05:17 PM
  4. New Crew seat and bass shaker
    By PaulEMB in forum My Cockpit Update
    Replies: 1
    Last Post: 08-27-2007, 07:32 PM