Results 1 to 7 of 7

Thread: Hurro

  1. #1
    10+ Posting Member
    Join Date
    Aug 2007
    Location
    Perth
    Posts
    12
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hurro

    Hello everyone, my name is Laurence, and I live in Northam - about 100km from Perth in the land of OZ - formally a former resident of ChCh NZ, and now starting to work on a 737- most likely 600 series (don't need that big a private jet)

    I've got the PM range of software that I've had for a few years. Whilst in NZ I was spoilt by seeing the awesome job the Flight Experience crew at work - well they don't call it work. Back then they were building the 767 - and when I returned to NZ just recently got to see their 737 - made me cry - I wish I could do something that good.

    I'm not looking top of the range - more likely everything will be made from mdf - I would buy them if I could find them cheap enough - but I find that a lot of panels are higher than I need.

    I've been building around the classic FSBus - as I had the stuff in NZ to do my own etchings etc - but may switch to opencockpit software.

    My biggest problem at this stage is tools - the only thing I have here is an electric drill - so yeah, buying panels rather than creating them (did a crappy job even with tools in NZ) would be better for me.

    But anyways - that's where I'm at, thought I would pop in and say hi

  2. #2
    Boeing 777 Builder


    Kennair's Avatar
    Join Date
    Jan 2007
    Location
    Perth, Western Australia
    Posts
    730
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Welcome to another WA resident Gaspode (?) I'm fairly new to this site also.

    I'm in Perth building a PC12 sim so I have no choice but to make panels. This and other forums are full of 737 builders so there's plenty of help available.

    Good luck and look forward to sharing the experience.

    Ken.
    Opencockpits | Aerosim Solutions | Sim-Avionics | P3D | FDS | FTX | AS16 | PPL | Kennair


  3. #3
    Executive Vice President, MyCockpit


    Matt Olieman's Avatar
    Join Date
    Oct 2005
    Location
    Ocala, FL USA
    Posts
    2,884
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Smile Welcome

    Welcome aboard Laurence, look forward to see your progress here

    You mentioned tools.... I know the feeling... seems I've invested quite a bit into tools to build my project, AND, learning new skills that came with the new tools

    Good luck on your project, again, I look forward toward seeing your progress and input

  4. #4
    MyCockpit Support Staff


    Westozy's Avatar
    Join Date
    Nov 2005
    Location
    Perth, Western Australia
    Posts
    1,415
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    G'day to another westozy!

    Gwyn

    737NG using Prosim737, Immersive Calibration Pro, Aerosim Solutions motorized TQ & cockpit hardware, CP Flight MCP & FDS SYS1X, SYS2X & SYS4X, FDS PRO FMCs, AFDS units & Glarewings, Matrix Orbital ELEC display, Pokeys Landing & Cruise alt display, Buttkicker Gamers, 3 x BenqMW811ST projectors with a Matrox Th2Go
    http://www.aerosimsolutions.com.au
    Supporter of MyCockpit.org, please join me in donating!!!

  5. #5
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    And yet another.. When will it end??!!! Just kidding guys, I have a tendency to get carried away!!! Welcome and I am looking forward to following your project. Hey Ken, have any pictures to share??!!!!
    Bob Reed

  6. #6
    10+ Posting Member
    Join Date
    Aug 2007
    Location
    Perth
    Posts
    12
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Quote Originally Posted by Kennair View Post
    Welcome to another WA resident Gaspode (?) I'm fairly new to this site also.
    Ken.

    Gaspode - A Talking Dog from Terry Pratchett

  7. #7
    300+ Forum Addict jmig's Avatar
    Join Date
    Apr 2007
    Location
    Lafayette, LA USA
    Posts
    422
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Welcome from a Yankee. Well, actually I am not a Yankee (dems were fighting words when I was a kid) unless you are from down where the world turns the wrong way.

    So, welcome anyway.
    John

    System:
    ASUS P5Q SE/R
    Intel Q9550 O/C to 3.4 GHz
    4 GB 1066 DDR2 RAM
    300 GB WD 10,000 RPM Raptor SATA Drive
    GeForce 8800 GT 512 KB RAM
    Matrox TH2Go with three 19" Sumsung 940 BX
    IR Track 4