Results 1 to 8 of 8
  1. #1
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Afternoon aggravation

    I've had three Boeing lightplates sitting around for months waiting to be installed onto the overhead to replace my scratch-built acrylic fake plates.

    So I decide I finally am going to install these today on my day off. I remove the old plates, the switches, etc., I drill new holes in the backplate for the switches and new screw holes.

    Run a quick lamp check after wiring the lightplate into the system and then attach it to the overhead, install the switches and admire my handi-work...

    Only to find that now the switch shafts are too short to put the knobs back on.



    The Boeing lightplates are twice as thick as what I made.

    Time for a hardware store run for some brass tubing.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  2. #2
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I have run into that a few times myself! Don't you just hate it??!!
    Bob Reed

  3. #3
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Yeah I do.

    I'm back from the store, but they didn't have any brass or aluminum tubing.

    Sooooo....

    I bought a 1/4" wood dowel and some 1/16" roll pins. I'm going to drill a hole in the end of the shaft, insert a roll pin and do the same for a short section of dowel rod and then JB Weld the two together.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  4. #4
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Is all the stuff we builders want really that off the wall?
    Bob Reed

  5. #5
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    That worked out very well. I used the Loc-Tite 401 instead of the JB Weld. The pins were pretty tight, so I didn't need the strength of the JB.

    I think I'll wait and do the other two tomorrow. I didn't think it would take three hours just to install a light plate!
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  6. #6
    1000+ Poster - Fantastic Contributor AndyT's Avatar
    Join Date
    Jun 2006
    Location
    Oahu, Hawaii
    Posts
    1,236
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    I had the same problem on my Cessna MIP. I solved it by using my router to make a shallow depression on the back side for the switch body to sit inside of. That allowed the shaft to stick out further and had the added effect of helping to secure the switch in place.
    God's in command, I'm just the Pilot.
    http://www.geocities.com/andytulenko/

  7. #7
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Great idea.

    The problem on a Boeing is that the backing plate is about 20ga. sheet steel spot welded to the overhead framework.

    On my scratchbuilt overhead the backing plate for all of the overhead interior and exterior switches was 1/8" plywood.

    With the switches mounted in the backing plate, and then the light plates being 3/16" thicker than the originals I made, I got a surprise.

    Everything is working fine now and the knobs are mounted to the extended shafts. I guess I'll do the other two tomorrow.
    Last edited by Michael Carter; 04-24-2007 at 07:37 PM.
    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING

  8. #8
    2000+ Poster - Never Leaves the Sim Michael Carter's Avatar
    Join Date
    Oct 2006
    Location
    Southern Illinois, USA
    Posts
    2,887
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Great idea.

    The problem on a Boeing is that the backing plate is about 20ga. sheet steel spot welded to the overhead framework.

    On my scratchbuilt overhead the backing plate for all of the overhead interior and exterior switches was 1/8" plywood.

    With the switches mounted in the backing plate, and then the light plates being 3/16" thicker than the originals I made, I got a surprise.

    Everything is working fine now and the knobs are mounted to the extended shafts. I guess I'll do the other two tomorrow.

    Boeing Skunk Works
    Remember...140, 250, and REALLY FAST!

    We don't need no stinkin' ETOPS!



    Powered by FS9 & BOEING