Results 1 to 7 of 7
  1. #1
    150+ Forum Groupie michelmvd's Avatar
    Join Date
    Nov 2005
    Location
    Oostende - Belgium
    Posts
    222
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Gear instructions

    Hello,
    I'm looking for the instruction you have to put in FS2Phidget (equal to "G" keystroke). Which offset can I use to activate single switch ?
    Many thanks for most appreciated help
    Michel
    _______________________________________________
    Michel VANDAELE
    msn : michelmvd@hotmail.com
    website B744 : users.telenet.be/michel.vandaele/sim1.htm
    general website : users.telenet.be/michel.vandaele
    my spaces: http://michelmvd.spaces.live.com/
    email : michelmvd@hotmail.com

  2. #2
    75+ Posting Member PeterH's Avatar
    Join Date
    Dec 2006
    Location
    EDDM
    Posts
    148
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi Michel,

    the FS offset: for Gear up dec. 66079 = hex 1021F
    for Gear down dec. 66080 = hex 10220

    Hope this is what you are after

    Best rgds

    Peter

  3. #3
    150+ Forum Groupie michelmvd's Avatar
    Join Date
    Nov 2005
    Location
    Oostende - Belgium
    Posts
    222
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Thanks a lot then it looks that I will need to swiches in the gear box
    Greetings
    Michel
    _______________________________________________
    Michel VANDAELE
    msn : michelmvd@hotmail.com
    website B744 : users.telenet.be/michel.vandaele/sim1.htm
    general website : users.telenet.be/michel.vandaele
    my spaces: http://michelmvd.spaces.live.com/
    email : michelmvd@hotmail.com

  4. #4
    1000+ Poster - Fantastic Contributor Bob Reed's Avatar
    Join Date
    Oct 2005
    Location
    Holley, New York U.S.A.
    Posts
    1,776
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    You could use one offset for when the switch is on and the other for when the switch is off. That would give you your 2 offsets as well.
    Bob Reed

  5. #5
    150+ Forum Groupie michelmvd's Avatar
    Join Date
    Nov 2005
    Location
    Oostende - Belgium
    Posts
    222
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Hi Bob, hmmmm can this be done with FS2Phidget ?
    B. Rgds
    Michel
    _______________________________________________
    Michel VANDAELE
    msn : michelmvd@hotmail.com
    website B744 : users.telenet.be/michel.vandaele/sim1.htm
    general website : users.telenet.be/michel.vandaele
    my spaces: http://michelmvd.spaces.live.com/
    email : michelmvd@hotmail.com

  6. #6
    alandyer
    Guest
    Michel,

    One offset (gear handle).

    Two Values for Offset (gear up and gear down).

    One switch with two Values (on and off).

    Use Fs2Phidget (or any solution supporting Digital Input) to:
    assign Gear up Offset value to a switch's Off position
    assign Gear down Offset value to a switch's On position.

    Gear Offset: 0BE8
    Offset values: 0 = Up, 16383 = Down

    Regards,
    Alan.

  7. #7
    150+ Forum Groupie michelmvd's Avatar
    Join Date
    Nov 2005
    Location
    Oostende - Belgium
    Posts
    222
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Okidoki Alan, its is working.
    Many thanks for your super support.
    Ciao
    Michel
    _______________________________________________
    Michel VANDAELE
    msn : michelmvd@hotmail.com
    website B744 : users.telenet.be/michel.vandaele/sim1.htm
    general website : users.telenet.be/michel.vandaele
    my spaces: http://michelmvd.spaces.live.com/
    email : michelmvd@hotmail.com

Similar Threads

  1. CNC Gear Machining
    By Westozy in forum Westozy's Mechanical Engineering
    Replies: 6
    Last Post: 12-06-2009, 04:32 AM
  2. gear up gear down
    By Radar in forum Where to Start Building a Home Cockpit
    Replies: 47
    Last Post: 04-14-2007, 01:00 AM