Results 1 to 4 of 4
  1. #1
    Phil Waecker
    Guest

    Transfer bus off annunciators

    Hello,

    I have one question concerning the Transfer Bus annunciators on the 737
    panel.

    Those are defined as textlightboxes with the following var transbus1=off. If
    I understand correctly this means it lights when transbus1 value is set to
    off. Up to there no problem.
    What I don't understand is that when we cut the power, batt to off the
    transbus1 variable is off but it doesn't light !

    How is this done ?

    Regards

    Phil


  2. #2
    Thomas Richter
    Guest

    Re: Transfer bus off annunciators

    Hi Phil,
    it is done inside pmSystems.
    When Batt1 is switch to OFF all TextLightBoxes and Gauges are going to OFF,

    also if they are in the background are ON.

    --
    Best Regards
    Thomas Richter

    "Phil Waecker" schrieb im Newsbeitrag
    news:407769.81482@wb.onvix.com...
    > Hello,
    >
    > I have one question concerning the Transfer Bus annunciators on the 737
    > panel.
    >
    > Those are defined as textlightboxes with the following var transbus1=off.


    > If
    > I understand correctly this means it lights when transbus1 value is set

    to
    > off. Up to there no problem.
    > What I don't understand is that when we cut the power, batt to off the
    > transbus1 variable is off but it doesn't light !
    >
    > How is this done ?
    >
    > Regards
    >
    > Phil
    >



  3. #3
    Phil Waecker
    Guest

    Re: Transfer bus off annunciators

    Thanks very much for this answer ! I was suspecting something like that but
    had never been confronted to the problem before. Since I am now connecting
    the overhead to IOCards hardware I noticed that those transfer bus lights
    remained always on !

    Nice evening

    Phil


  4. #4
    Thomas Richter
    Guest

    Re: Transfer bus off annunciators

    Hi Phil,
    I use also IOCards (with SIOC) and Phidgets.
    I will upload in some days a new 737NG098-file, there I use new Offsets:
    TransBus1Fault, ....
    Because I had the same problem, so I changed the logic.

    --
    Best Regards
    Thomas Richter

    "Phil Waecker" schrieb im Newsbeitrag
    news:407847.81482@wb.onvix.com...
    > Thanks very much for this answer ! I was suspecting something like that
    > but
    > had never been confronted to the problem before. Since I am now

    connecting
    > the overhead to IOCards hardware I noticed that those transfer bus lights
    > remained always on !
    >
    > Nice evening
    >
    > Phil
    >



Similar Threads

  1. Sound transfer
    By Geremy Britton in forum FS2004 Sound Discussions
    Replies: 6
    Last Post: 06-25-2009, 07:24 AM
  2. Replies: 5
    Last Post: 07-25-2008, 10:36 AM
  3. Best Method of Program Transfer??
    By Michael Carter in forum Computer Hardware Setup
    Replies: 18
    Last Post: 11-12-2007, 01:50 AM
  4. PM Software harddisk transfer to new PC
    By chrisdanker in forum PM General Q & A
    Replies: 8
    Last Post: 03-09-2007, 06:46 AM
  5. Phidget Forum Transfer Complete
    By Matt Olieman in forum MyCockpit News and Announcements
    Replies: 0
    Last Post: 02-09-2007, 10:06 AM