Page 4 of 4 FirstFirst 1234
Results 31 to 35 of 35

Thread: A320 FMGS B52

  1. #31
    25+ Posting Member
    Join Date
    Sep 2015
    Location
    Germany
    Posts
    36
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Fire Agent 1 and 2

    Quote Originally Posted by capt_pero View Post
    Hi JL,

    great job. I just had an issue with the fire Agent 1 and 2.

    Expected:
    - Fire Engine 1
    - Press Fire handle Engine 1
    - Agent 1 SQUIB LED illuminated
    - after pressing Agent 1 DISCH and SQUIB is illuminated

    Is:
    - Fire Engine 1
    - Press Fire handle Engine 1
    - Agent 1 DISCH and SQUIB is illuminated
    - after pressing Agent 1 DISCH and SQUIB is illuminated

    This is the same for all Agents on both engines. Can you verify?
    Can be reproduced with SW Overhead Panel (HW independent).

    Regards,
    Peter
    Hi Peter!

    How do you setup the failure? As I remember there is no way to trigger "real" failures in Jeehell FMGS. The only workaround is to set the Fire Test button offset through an external script to simulate an engine fire. JL, correct me if I'm wrong.
    And for Fire Test it should be normal that all Korry LEDs and the Fire handle illuminate.
    Best regards
    Karsten

  2. #32
    75+ Posting Member
    Join Date
    Oct 2013
    Location
    Germany
    Posts
    107
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: Fire Agent 1 and 2

    Hi Karsten,

    good to know. Is there any other option to create engine fire?

    Regards,
    Peter

  3. #33
    300+ Forum Addict
    Join Date
    Sep 2010
    Location
    LGTS
    Posts
    378
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B52

    1. When I push or pull to descent from CRZ ALT to a lower altitude, the A/C always enters in descent phase, but I think this shouldn't be happen when distanse drom destination is greater than 200NM. In that case NEW CRZ ALT should be appeared in MCDU just like when we climb.

    2. Does anybody know what this red arrow is during final approach? I've seen this only during takeoff, when I pull sidestick more than it should.

    Attached Images Attached Images

  4. #34
    2000+ Poster - Never Leaves the Sim
    Join Date
    Mar 2008
    Location
    France,Nice
    Posts
    2,549
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B52

    @Leonidas:
    1. actually it is less than 200NM from dest OR selected ALT on FCU <= FL200 to trigger DES phase. I will check but it should be working?
    2. this is for tailstrike awareness, it is optionnal.

  5. Thanks Leonidas thanked for this post
  6. #35
    300+ Forum Addict
    Join Date
    Sep 2010
    Location
    LGTS
    Posts
    378
    Contribute If you enjoy reading the
    content here, click the below
    image to support MyCockpit site.
    Click Here To Contribute To Our Site

    Re: A320 FMGS B52

    Quote Originally Posted by jeehell View Post
    @Leonidas:
    1. actually it is less than 200NM from dest OR selected ALT on FCU <= FL200 to trigger DES phase. I will check but it should be working?
    Test it again, so: when descent at >200NM in MCDU PERF page remains to CRZ page as it should. But:
    INIT CRZ FL remains the same
    PROG CRZ remains the same
    FMA says ALT not ALT CRZ

    Regards

Page 4 of 4 FirstFirst 1234